Extreme Networks ExtremeSwitching X440-G2 Series Скачать руководство пользователя страница 40

Страница: 40 / 413

Table 7: X450-G2 Front Panel LEDs (continued)

Label or Type

Color/State

Meaning

FAN

Steady green

Normal operation

Blinking amber

Failure

Off

No power

P1, P2 (Power Supply)

Steady green

Normal operation

Steady amber

Power is attached, but no power is on

Blinking amber

Power failure

Off

No power attached

Ethernet Port 1–24 or 1–48

Steady green

Link OK

Blinking green

Activity on the indicated port

Off

No link or port disabled

1G SFP ports or 10G SFP+
ports 25, 26, 27, and 28 or
49, 50, 51, and 52

Steady green

Link OK

Blinking green

Activity on the indicated port

Off

No 1G or 10G link, or port disabled

Table 8: Additional Port LED Meanings for PoE Switches: X450-G2-24p-GE4, X450-
G2-24p-10GE4, X450-G2-48p-GE4, and X450-G2-48p-10GE4

Label or Type

Color/State

Meaning

All front panel ports 1-24 or
1-48

Steady green

Link is OK; port is not powered

Steady amber

Link is OK; port is powered; no traffic

Blinking green

Link is OK and transmitting packets; port is not
powered

Blinking amber

Link is OK and transmitting packets; port is
powered

Slow blinking amber

No link, or disabled port; port is powered

Alternating amber and green

Port has a power fault

Off

Port is not powered, has no link, or is disabled

Table 9: X450-G2 2-digit Stack Number Indicator

Label or Type

Color/State

Meaning

Left digit (1)

Reserved for future use.

Right digit (1–8)

Indicates the position of this switch in the SummitStack configuration

Upper half blinking

This switch is the stack master node

Lower half blinking

This switch is the stack backup node

Lit steadily

This switch is a standby node in the stack

ExtremeSwitching Switches

ExtremeSwitching and Summit Switches: Hardware Installation Guide

Содержание ExtremeSwitching X440-G2 Series






























































































































































































































































































































































































































Результаты поиска

Содержание ExtremeSwitching X440-G2 Series

Отзывы:

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренды по названию

Популярные бренды

Extreme Networks ExtremeSwitching X440-G2 Series, Руководство по установке оборудования

Результаты поиска

Содержание ExtremeSwitching X440-G2 Series

Отзывы:

Похожие инструкции для ExtremeSwitching X440-G2 Series

Бренды по названию

Популярные бренды