43
42
EN
EN
Meets respective
EU requirements.
0.5 m
The minimum clearance between
the lighting device and the illumina-
ted item must be 0.5 m.
Only use the floodlight with the
undamaged front cover installed.
Replace a cracked protective front
cover.
t
a
...°C
Highest nominal ambient tem-
perature.
Do not place the lighting device in the
vicinity of easily flammable materials
and on easily flammable materials.
Do not use in an environment where
there is a risk of explosion or fire.
Non-dimming light source.
Read the user's manual before use.
Do not dispose of unserviceable
commodities in household waste,
but dispose of / recycle them in an
environmentally safe manner.
Table 3
VI. Waste disposal
y
Throw packaging materials into a container for the
respective sorted waste.
y
The product contains electronic components that
constitute hazardous waste. According to
European Directive No. 2012/19 EU, electric appli-
ances must not be thrown out with household
waste, and must be handed over for ecological
disposal at specified collection points. You can find information
about these collection points at your local town council office.
EU Declaration of Conformity
Manufacturer Madal Bal a.s. • Bartošova 40/3
760 01 Zlín • Company ID No.: 49433717
declares that the products designated below, on the basis of
their design and construction, as well the configuration in
which they were brought on to the market, comply with the
relevant requirements of the European Union. This declarati-
on becomes void in the event of modifications to the product
that are not approved by us. This declaration is issued under
the exclusive responsibility of the manufacturer.
Extol® Light 43221; 43232; 43223
LED Floodlights
were designed and produced in conformity with the
following standards:
EN 60598-1:2015; EN 60598-2-5:2015;
EN 55015:2013+A1; EN 61547:2009; EN 61000-3-2:2014;
EN 61000-3-3:2013; EN 62321:2008
and harmonisation directives:
2014/35 EU; 2014/30 EU; 2011/65 EU; 2009/125 EC
(EU Commission Directive no. 1194/2012 for ecodesign)
In Zlín 19. 7. 2016
Martin Šenkýř, Member of the Board of Directors
20 cm
Fig. 3
y
On the floodlight with the motion switching sensor,
the floodlight will light up depending on the motion
at dusk and at night. The switching detection distan-
ce and the lighting time are factory set and it is not
permitted for the user to adjust this themselves.
•
ATTENTION
y
Protect the power cord of the floodlight against ther-
mal and mechanical damage. In the event of damage,
immediately turn off the floodlight, disengage the
voltage in the grid and organise a repair at an autho-
rised service centre for the Extol® brand.
y
The floodlight has a non-replaceable light source, which
when not mechanically damaged has a lifespan of more
than 30,000 hours and thus under normal circumstances
it is not necessary to remove the floodlight‘s front cover.
y
For safety reasons, do not cover the floodlight
during operation; circulation of ambient air must be
provided for. Likewise, do not install or operate the
floodlight in a confined small area with an insuffici-
ent volume and circulation of air.
IV. Cleaning,
maintenance, repairs
y
In the event that the floodlight requires cleaning, first
unplug it from the el. power supply and allow it to cool
down. Do not use abrasive cleaning products and organic
solvents to clean the floodlight as this would damage it.
y
Service adjustment or installation of the floodlight
must be performed with the power supply turned off.
y
In the event that the power cord itself is damaged,
do not use the floodlight and have it replaced at
an authorised service centre for the Extol® brand.
Disconnect the floodlight from the el. power source
with the el. power source turned off.
y
In the event of damage to the protective front cover of the
floodlight, replace it with a new one. For safety reasons, it
is not possible to use the floodlight with a damaged pro-
tective front cover. If the user replaces the protective front
glass, the manufacturer can no longer guarantee the IP65
protection class with protection against the damaging
entry of water and dust because the manufacturer cannot
be responsible for the possible incorrect installation of the
protective front cover by the user.
When the protective cover is replaced, the same level
of protection must be ensured as in the original con-
figuration. The original gasket seal from the manu-
facturer must be used. When the glass is replaced,
the gasket seal must be completely undamaged and
untwisted. The glass must have the same thickness
as the original. In the event that these requirements
are not met, the provided level of protection will be
insufficient against the entry of water and dust, and
the floodlight must not be exposed to rain, moisture
or other form of water entry and dangerous touching.
y
For warranty repairs, please contact the vendor
from whom you purchased the product and they will
organise repairs at an authorised service centre for
the Extol® brand. For a post warranty repair, please
contact the authorised service centre of the Extol®
brand directly (you will find the repair locations at
the website at the start of this user‘s manual).
V. References to the label
and pictograms
