EWM Phoenix 401 Progress puls MM FKW Скачать руководство пользователя страница 103 | Manualshive

Страница: 103 / 123

background image

Design and function

Machine configuration menu

099-005323-EW501

21.05.2014

103

Mean value display for super pulses (P19)

Function active (P19 = 1)

• For super pulses, the mean power from program A (P

A

) and program B (P

B

) is shown in the display

(factory setting).

Function inactive (P19 = 0)

• Only power from program A is displayed for super pulses.

NOTE

If the function is enabled and only "000" is shown on the machine display, this is a rare
case of an incompatible system set-up. Solution: Disable special parameter P19.

Predefined execution of the pulsed arc welding process in the PA program (P20)

NOTE

Pulse arc welding machines only.

Function active (P20 = 1)

• If the superPuls and welding process switching functions are available and activated, the pulsed arc

welding process is always executed in the main program PA (ex factory).

Function inactive (P20 = 0)

• Predefined execution of the pulsed arc welding process in the PA program is disabled.

Predefined absolute value for relative programs (P21)

Start program (P

START

), down-slope program (P

B

) and end program (P

END

) can be set relative to the main

program (P

A

) or in an absolute manner, as desired.

Function active (P21 = 1)

• Absolute parameter setting

Function inactive (P21 = 0)

• Relative parameter setting (ex factory)

5.16

Machine configuration menu

5.16.1

Selecting, changing and saving parameters

NOTE

ENTER (Enter the menu)

• Switch off the machine at the main switch.
• Press and hold the "welding parameters" push-button and switch the machine on again at

the same time.

NAVIGATION (Navigate the menu)

• Select parameters by turning the "welding parameter setting" rotary knob.
• Set or change parameters by turning the "arc length correction/select welding program"

rotary knob.

EXIT (Exit the menu)

• Press the "parameter selection right" push-button (switch machine off and on again).

«
...
101
102
103
104
105
...
»

Содержание Phoenix 401 Progress puls MM FKW




























































































































Отзывы:

Нет отзывов

Похожие инструкции для Phoenix 401 Progress puls MM FKW

Бренд: Wayne-Dalton Страницы: 24

Бренд: UniPOS Страницы: 2

Бренд: Nabco Страницы: 50

Бренд: Nabco Страницы: 43

Бренд: Nabco Страницы: 10

Бренд: Ibiza Страницы: 24

Бренд: i3-TECHNOLOGIES Страницы: 19

Бренд: jablotron Страницы: 17

Бренд: R-Tech Страницы: 57

Liberty Vertical Picket

Бренд: National ramp Страницы: 9

STExB2X05-S Series

Бренд: E2S Страницы: 20

Бренд: VENCO Страницы: 31

Бренд: R. Beck Maschinenbau Страницы: 34

Бренд: Falcon Страницы: 3

Бренд: Nalnor Страницы: 8

Бренд: Bard Страницы: 54

Бренд: Lampert Страницы: 22

Бренд: Parweld Страницы: 16

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды