EWM Phoenix 401 Progress puls MM FKW Скачать руководство пользователя страница 94

Страница: 94 / 123

Design and function

Special parameters (advanced settings)

099-005323-EW501

21.05.2014

Display

Setting/selection

Predefined execution of the pulsed arc welding process in the PA program

0 =

Predefined execution of the pulsed arc welding process in the PA program is
disabled.

1 =

If the superPuls and welding process switching functions are available and
activated, the pulsed arc welding process is always executed in the main
program PA (ex factory).

Predefined absolute value for relative programs

Start program (P

START

), down-slope program (P

) and end program (P

END

) can be set

relative to the main program (P

) or in an absolute manner, as desired.

0 =

Relative parameter setting (ex factory)

1 =

Absolute parameter setting

5.15.2

Reset to factory settings

NOTE

All special parameters saved by the user will be overwritten by the factory settings!

Operating
element

Action

Result

Switch off welding machine

Keep the button pressed

Switch on welding machine

Release the button, wait about 3 seconds

Switch off welding machine and restart in order to put the changes into
effect

Содержание Phoenix 401 Progress puls MM FKW




























































































































Результаты поиска

Содержание Phoenix 401 Progress puls MM FKW

Отзывы:

Похожие инструкции для Phoenix 401 Progress puls MM FKW

Бренды по названию

Популярные бренды

EWM Phoenix 401 Progress puls MM FKW, Руководство по эксплуатации

Результаты поиска

Содержание Phoenix 401 Progress puls MM FKW

Отзывы:

Похожие инструкции для Phoenix 401 Progress puls MM FKW

Бренды по названию

Популярные бренды