EWM Phoenix 401 Progress puls MM FKW Скачать руководство пользователя страница 32 | Manualshive

Страница: 32 / 123

background image

Design and function

Shielding gas supply (shielding gas cylinder for welding machine)

32

099-005323-EW501

21.05.2014

5.7

Shielding gas supply (shielding gas cylinder for welding machine)

WARNING

Risk of injury due to improper handling of shielding gas cylinders!
Improper handling and insufficient securing of shielding gas cylinders
can cause serious injuries!

• Secure shielding gas cylinders using the standard fastening elements on

the unit (chain/belt)!

• The fastening elements must tightly enclose the shielding gas cylinder!
• Attach the fastening elements within the upper half of the shielding gas

cylinder!

• Do not attach any element to the shielding gas cylinder valve!
• Observe the instructions from the gas manufacturer and any relevant

regulations concerning the use of compressed air!

• Avoid heating the shielding gas cylinder!

CAUTION

Faults in the shielding gas supply.
An unhindered shielding gas supply from the shielding gas cylinder to the welding
torch is a fundamental requirement for optimum welding results. In addition, a blocked
shielding gas supply may result in the welding torch being destroyed.

• Always re-fit the yellow protective cap when not using the shielding gas connection.
• All shielding gas connections must be gas tight.

NOTE

Before connecting the pressure regulator to the gas cylinder, open the cylinder valve
briefly to expel any dirt.

• Place the shielding gas cylinder into the relevant cylinder bracket.
• Secure the shielding gas cylinder using a securing chain.

Figure 5-3

Item Symbol

Description

0

1

Pressure regulator

2

Shielding gas cylinder

3

Output side of the pressure regulator

4

Cylinder valve

•  Tighten the pressure regulator screw connection on the gas bottle valve to be gas-tight.
•  Screw gas hose connection crown nut onto the output side of the pressure regulator.
•  Fasten the gas hose to the shielding gas connecting nipple at the back of the machine using the crown

nut.

«
...
30
31
32
33
34
...
»

Содержание Phoenix 401 Progress puls MM FKW




























































































































Отзывы:

Нет отзывов

Похожие инструкции для Phoenix 401 Progress puls MM FKW

security system

Бренд: Safe-at-home Страницы: 5

Бренд: Palfinger Страницы: 34

Бренд: Panasonic Страницы: 124

Бренд: Xilica Audio Design Страницы: 28

Бренд: Eco Страницы: 112

Бренд: Magellan Страницы: 2

Бренд: Parkside Страницы: 54

Бренд: MAHA Страницы: 23

SAF-FRO PRESTOTIG 240 AC/DC

Бренд: Air Liquide Страницы: 121

Бренд: Amico Страницы: 4

CIRFLEXX UMS 4100

Бренд: Grundig Страницы: 38

SystemRoMedic SlingBarSpreader M

Бренд: Handicare Страницы: 3

Бренд: JBL Страницы: 16

ThermoPro G4 Series

Бренд: Curtis Страницы: 40

Scalekleen EV9796-01

Бренд: Everpure Страницы: 2

Бренд: M-system Страницы: 3

Бренд: C&K systems Страницы: 2

Бренд: Ibiza sound Страницы: 50

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды