EWM Phoenix 401 Progress puls MM FKW Скачать руководство пользователя страница 12 | Manualshive

Страница: 12 / 123

background image

Safety instructions

General

12

099-005323-EW501

21.05.2014

CAUTION

EMC Machine Classification
In accordance with IEC 60974-10, welding machines are grouped in two electromagnetic
compatibility classes (see technical data):
Class A

machines are not intended for use in residential areas where the power supply comes

from the low-voltage public mains network. When ensuring the electromagnetic compatibility of
class A machines, difficulties can arise in these areas due to interference not only in the supply
lines but also in the form of radiated interference.

Class B

machines fulfil the EMC requirements in industrial as well as residential areas,

including residential areas connected to the low-voltage public mains network.

Setting up and operating

When operating arc welding systems, in some cases, electro-magnetic interference can occur
although all of the welding machines comply with the emission limits specified in the standard.
The user is responsible for any interference caused by welding.

In order to

evaluate

any possible problems with electromagnetic compatibility in the

surrounding area, the user must consider the following: (see also EN 60974-10 Appendix A)
•  Mains, control, signal and telecommunication lines
•  Radios and televisions
•  Computers and other control systems
•  Safety equipment
•  The health of neighbouring persons, especially if they have a pacemaker or wear a hearing

aid

•  Calibration and measuring equipment
•  The immunity to interference of other equipment in the surrounding area
•  The time of day at which the welding work must be carried out

Recommendations for

reducing interference emission

•  Mains connection, e.g. additional mains filter or shielding with a metal tube
•  Maintenance of the arc welding equipment
•  Welding leads should be as short as possible and run closely together along the ground
•  Potential equalization
•  Earthing of the workpiece. In cases where it is not possible to earth the workpiece directly,

it should be connected by means of suitable capacitors.

• Shielding from other equipment in the surrounding area or the entire welding system

«
...
10
11
12
13
14
...
»

Содержание Phoenix 401 Progress puls MM FKW




























































































































Отзывы:

Нет отзывов

Похожие инструкции для Phoenix 401 Progress puls MM FKW

Бренд: ABB Страницы: 20

Бренд: Panasonic Страницы: 2

RXD15 - RADIO CASSETTE W/CD

Бренд: Panasonic Страницы: 8

Бренд: abc Страницы: 8

Бренд: FAAC Страницы: 12

Бренд: Gamewell Страницы: 21

Бренд: Garmin Страницы: 10

Hard Top Lifter

Бренд: Garage Smart Страницы: 20

JBL BAR 5.1 SURROUND

Бренд: Harman Страницы: 4

Бренд: Harman Страницы: 48

Infinity KAPPA 4100msb

Бренд: Harman Страницы: 8

JBL PARTYBOX ON-THE-GO

Бренд: Harman Страницы: 17

Бренд: R. Beck Maschinenbau Страницы: 35

JBL CINEMA SB190

Бренд: Harman Страницы: 19

Бренд: Eaton Страницы: 23

Бренд: dallmeier Страницы: 2

Бренд: Samsung Страницы: 33

Бренд: 1 Sound Страницы: 92

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды