EWM Phoenix 401 Progress puls MM FKW Скачать руководство пользователя страница 14 | Manualshive

Страница: 14 / 123

background image

Safety instructions

Transport and installation

14

099-005323-EW501

21.05.2014

2.4.1

Lifting by crane

WARNING

Risk of injury during lifting by crane

!

When lifting the machine by crane, persons may be severely injured by falling machines
or mount-on components.

• Simultaneous lifting

of system components such as power source

,

wire

feeder or cooling unit

is not allowed. Each system component has to

be lifted separately!

• Remove any supply leads and accessories before lifting by crane

(e.g.

hose package

,

wire spool

,

shielding gas cylinder

,

toolbox, wire feeder

,

remote control,etc.)!)

• Properly close and lock all casing covers and protective caps

before

lifting by crane!

• Use the correct number of hoisting equipment of the right size and

right capacity! Observe craning principle (see figure)!

• For machines with lifting eyes: always lift all lifting eyes simultaneously

!

• When using retrofitted craning frames etc.: always use at least two

lifting points positioned as far apart as possible

– observe option

description.

• Avoid any jerky movements!
• Ensure that the load is

distributed evenly! • Use chain hoists and

chain slings of the same length only!

• Stay outside the danger zone underneath the machine!
• Observe the regulations regarding occupational safety and accident

prevention for the respective country.

Craning principle

Risk of injury due to unsuitable lifting eye!
In case of improper use of lifting eyes or the use of unsuitable lifting eyes, persons can
be seriously damaged by falling equipment or add-on components!

•  The lifting eye must be completely screwed in!
•  The lifting eye must be positioned flat onto and in full contact with the supporting surfaces!
•  Check that the lifting eyes are securely fastened before use and check for any damage

(corrosion, deformation)!

• Do not use or screw in damaged lifting eyes!
• Avoid lateral loading of the lifting eyes!

«
...
12
13
14
15
16
...
»

Содержание Phoenix 401 Progress puls MM FKW




























































































































Отзывы:

Нет отзывов

Похожие инструкции для Phoenix 401 Progress puls MM FKW

Бренд: Yale Страницы: 10

Бренд: OMA Страницы: 73

Бренд: Magnavox Страницы: 26

FSA ECO SR-EFR BG

Бренд: Eco Страницы: 23

Бренд: FAAC Страницы: 4

Бренд: FAAC Страницы: 30

Бренд: FältCom Страницы: 40

Бренд: Mackie Страницы: 6

Бренд: Mackie Страницы: 6

Бренд: Mackie Страницы: 12

Fussion Series 3000

Бренд: Mackie Страницы: 8

Fussion Series 3000

Бренд: Mackie Страницы: 8

Art Series ART300

Бренд: Mackie Страницы: 6

Art Series ART200A

Бренд: Mackie Страницы: 2

Бренд: Najm Alfarqadain Страницы: 2

Бренд: VENCO Страницы: 44

Бренд: Wabtec Страницы: 106

ZS 80 KST Extreme Series

Бренд: steute Страницы: 20

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды