EWM Phoenix 401 Progress puls MM FKW Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 123

background image

Design and function

Shielding gas supply (shielding gas cylinder for welding machine)

099-005323-EW501

21.05.2014

33

5.7.1

Gas test

•  Slowly open the gas cylinder valve.
•  Open the pressure regulator.
•  Switch on the power source at the main switch.
•  Initiate gas test function on the machine control.
•  Set the relevant gas quantity for the application on the pressure regulator.
•  The gas test is triggered on the machine control by pressing the

button briefly.

Shielding gas flows for around 25 seconds or until the button is pressed again.

5.7.2

“Rinse hose package” function

Operating
Element

Action

Result

5 s

Select rinse hose package.

Shielding gas flows continuously until the Gas Test button is pressed
again.

5.7.3

Setting the shielding gas quantity

Welding process

Recommended shielding gas quantity

MAG welding

Wire diameter x 11.5 = l/min

MIG brazing

Wire diameter x 11.5 = l/min

MIG welding (aluminium)

Wire diameter x 13.5 = l/min (100 % argon)

TIG

Gas nozzle diameter in mm corresponds to l/min gas throughput

Helium-rich gas mixtures require a higher gas volume!

The table below can be used to correct the gas volume calculated where necessary:

Shielding gas

Factor

75% Ar/25% He

1.14

50% Ar/50% He

1.35

25% Ar/75% He

1.75

100% He

3.16

NOTE

Incorrect shielding gas setting!
If the shielding gas setting is too low or too high, this can introduce air to the weld pool
and may cause pores to form.

• Adjust the shielding gas quantity to suit the welding task!

«
...
31
32
33
34
35
...
»

Содержание Phoenix 401 Progress puls MM FKW




























































































































Отзывы:

Нет отзывов

Похожие инструкции для Phoenix 401 Progress puls MM FKW

Бренд: KEF Страницы: 12

Бренд: D+H Страницы: 4

MagnaLatch ALERT

Бренд: D&D Technologies Страницы: 2

Бренд: L-Acoustics Страницы: 38

Бренд: L-Acoustics Страницы: 31

Бренд: L-Acoustics Страницы: 24

Бренд: L-Acoustics Страницы: 201

Aqua-Hot AHE-100-04S

Бренд: Vehicle Systems Страницы: 19

Бренд: VENCO Страницы: 44

Бренд: Wabtec Страницы: 106

Бренд: Yamaha Страницы: 7

Бренд: BlitzRotary Страницы: 41

Бренд: Westlake Audio Страницы: 21

Бренд: Mahe Страницы: 48

Бренд: Laser Страницы: 3

Бренд: Q-See Страницы: 10

Бренд: RED SHIELD Страницы: 9

VVH-MD657/AVM-360PV

Бренд: Vacron Страницы: 53

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды