EWM Expert XQ 2.0 Скачать руководство пользователя страница 9

Страница: 9 / 92

Intended use

Applications

099-00L105-EW501

07.06.2019

Intended use

WARNING

Hazards due to improper usage!

The machine has been constructed to the state of the art and any regulations and

standards applicable for use in industry and trade. It may only be used for the welding

procedures indicated at the rating plate. Hazards may arise for persons, animals and

material objects if the equipment is not used correctly. No liability is accepted for any

damages arising from improper usage!

• The equipment must only be used in line with its designated purpose and by trained or

expert personnel!

• Do not improperly modify or convert the equipment!

3.1 Applications

Device control of multi-process welding machines for arc welding covering the following welding proce-

dures:

Machine series

Main procedure for MIG/MAG welding

Secondary process

Standard arc

Pulsed arc

TIG

ldin

g (

lif

t ar

MMA

weldin

Goug

ing

G/MA

G X

forc

rc XQ

otA

rc XQ

ldA

G/MA

G pul

forc

rc puls

otA

rc pul

s XQ

ldA

uls

c pul

s XQ

Titan XQ / XQ C

Titan XQ AC

3.2 Use and operation solely with the following machines

The following system components can be combined:
This description may be applied only to machines with the Expert XQ 2.0 machine control.

Machine control

Expert XQ 2.0

Expert XQ 2.0 LG

Expert XQ 2.0 WLG

Description

No network connection

Version with LAN

Version with Wi-Fi and LAN

3.3 Documents which also apply

• Operating instructions for the connected welding machines
• Documents of the optional expansions

3.4 Software version

These instructions apply to the following software version:
2.0.D.0

The machine control software version is shown on the screen during the start

process

> see 4.3.3 chapter

Содержание Expert XQ 2.0





























































































Результаты поиска

Содержание Expert XQ 2.0

Отзывы:

Похожие инструкции для Expert XQ 2.0

Бренды по названию

Популярные бренды

EWM Expert XQ 2.0, Руководство по эксплуатации

Результаты поиска

Содержание Expert XQ 2.0

Отзывы:

Похожие инструкции для Expert XQ 2.0

Бренды по названию

Популярные бренды