EWM Expert XQ 2.0 Скачать руководство пользователя страница 74

Страница: 74 / 92

Welding procedure

TIG welding

099-00L105-EW501

07.06.2019

Non-latched mode

Figure 6-19

Selection

• Select non-latched operating mode

Step 1

• Press and hold torch trigger.
• Shielding gas is expelled (gas pre-flows).

The arc is ignited using liftarc.

• Welding current flows with pre-selected setting.

Step 2

•  Release torch trigger.
•  Arc is extinguished.
•  Gas post-flow time elapses.

Special, non-latched

Figure 6-20

Selection

• Select non-latched special mode

Step 1

• Press and hold torch trigger
• Shielding gas is expelled (gas pre-flows)

The arc is ignited using liftarc.

• Welding gas flows with pre-selected setting in start program “P

START

”.

• After the “tstart” ignition current time elapses, the welding current rises with the set upslope time “tS1”

to the main program “P

”.

Step 2

• Release torch trigger.
• The welding current reduces with the downslope time “tSe” to the end program “P

END

”.

• After the end current time “end” elapses, the arc will extinguish.
• Gas post-flow time elapses.

Содержание Expert XQ 2.0





























































































Результаты поиска

Содержание Expert XQ 2.0

Отзывы:

Похожие инструкции для Expert XQ 2.0

Бренды по названию

Популярные бренды

EWM Expert XQ 2.0, Руководство по эксплуатации

Результаты поиска

Содержание Expert XQ 2.0

Отзывы:

Похожие инструкции для Expert XQ 2.0

Бренды по названию

Популярные бренды