EWM Expert XQ 2.0 Скачать руководство пользователя страница 37

Страница: 37 / 92

Operating the machine control

Offline data transfer (USB)

099-00L105-EW501

07.06.2019

5.5.4 Load configuration

5.5.4.1 System

Configuration data of the power source’s system components.

5.5.4.2 Xnet machine

Master configuration

Core date for network communication (independent of machine).

Individual configuration

Machine-related configuration data, matching the current power source only.

5.5.5 Load languages and texts

Load a language and text package from the storage medium (USB) to the welding machine.

5.5.6 Record on USB drive

You can record welding data on a storage medium and read or analyse them using the Xnet quality ma-

nagement software when required. For machine variants with network capability (LG/WLG) only!

5.5.6.1 Register USB drive

To identify and allocate the welding data between power source and storage medium the storage medium

has to be registered once. This is done by selecting the menu option "Register USB drive" or by starting a

data recording process. Successful registration is indicated by a checkmark next to the relevant menu op-

tion.
If the storage medium is registered and connected when the power source is being switched on, record-

ing of the welding data starts automatically.

5.5.6.2 Start recording

After confirming the start of data recording the storage medium will be registered (if not registered yet).

Data recording starts and is indicated at the main screen by a slow flashing of the icon.

5.5.6.3 Stop recording

To avoid data loss, finish the recording with this menu option before removing the USB drive or switching

off the machine.

Welding data must be imported into the Xnet quality management software using the XWDImport

software. This software is an integral part of the Xnet installation.

Содержание Expert XQ 2.0





























































































Результаты поиска

Содержание Expert XQ 2.0

Отзывы:

Похожие инструкции для Expert XQ 2.0

Бренды по названию

Популярные бренды

EWM Expert XQ 2.0, Руководство по эксплуатации

Результаты поиска

Содержание Expert XQ 2.0

Отзывы:

Похожие инструкции для Expert XQ 2.0

Бренды по названию

Популярные бренды