EWM Expert XQ 2.0 Скачать руководство пользователя страница 18

Страница: 18 / 92

Operating the machine control

Machine configuration (system)

099-00L105-EW501

07.06.2019

The user can switch the lock function on or off by pressing the button for a long time from each machine
control or accessory component with the symbol

5.4 Machine configuration (system)

In the System menu the user can set the basic machine configuration.

Enter the menu:

Figure 5-1

5.4.1 Power-saving mode (Standby)

You can activate the power-saving mode by setting a parameter in the configuration menu (time-

controlled power-saving mode). When power-saving mode is active, the Expert XQ 2.0 machine controller

display is dimmed and only the middle digit of the display is shown in the wire feed unit. Pressing any

operating element (e.g. tapping the torch trigger) deactivates power-saving mode and the machine is

ready for welding again.

Menu item/parameter

Value

Comment

Time automatic [min.]

Off

Function switched off

5-60

Time to activation of the power-saving mode in

case of inactivity.

Log off user in standby mode

Yes

The user will be logged off when the power-

saving mode is active.

The user will not be logged off when the power-

saving mode is active.

Содержание Expert XQ 2.0





























































































Результаты поиска

Содержание Expert XQ 2.0

Отзывы:

Похожие инструкции для Expert XQ 2.0

Бренды по названию

Популярные бренды

EWM Expert XQ 2.0, Руководство по эксплуатации

Результаты поиска

Содержание Expert XQ 2.0

Отзывы:

Похожие инструкции для Expert XQ 2.0

Бренды по названию

Популярные бренды