EWM Expert XQ 2.0 Скачать руководство пользователя страница 23

Страница: 23 / 92

Operating the machine control

Machine configuration (system)

099-00L105-EW501

07.06.2019

5.4.4.4 Special parameter

The special parameters of the wire feeder control are used to customize the machine function configurati-

on.
The number of selectable special parameters can deviate between the machine controls used in the

welding system.
It may be required to restart the machine in order to apply a parameter change.
Systems with two wire feeder controls show the parameters of the active wire feeder only (special para-

meter U1 or special parameter U2).

Menu i-

tem/parameter

Value

Comment

1-0

Wire inching / wire return ramp time

0 =-------- normal inching (10 s ramp time)

1 =-------- fast inching (3 s ramp time) (ex works)

0-1

Block program "0"

0 =-------- Enabled (ex works)

1 =-------- P0 blocked

0-1

Display mode for Up/Down welding torch with one-digit 7-segment

display (two keys)

0 =-------- Normal display (ex works) program number/welding power

(0–9)

1 =-------- Display toggles between program number/welding type

0-1

Correction operation, limit value setting

0 =-------- Correction operation switched off (ex works)

1 =-------- Correction operation switched on

0-1

Program switching with standard welding torch

0 =-------- No program switching (ex works)

1 =-------- Special latched

2 =-------- Special latched (n-cycle active)

0-1

Tapping start for latched and special latched operation

0 =-------- no 4-cycle inching start

1 =-------- 4-cycle inching start possible (ex works)

P11

0-1

Special latched tapping time

0 =-------- Tapping function switched off.

1 =-------- 300 ms (ex works)

2 =-------- 600 ms

P12

1-2

JOB list switching

1 =-------- Real JOB list (ex works)

2 =-------- Real JOB list and JOB switching activated via accessories

P13

129

Lower limit remote JOB switching

JOB range of the function torches (MT PC2, PM 2U/D, PM RD2)

Lower limit: 129 (ex works)

P14

169

Upper limit remote JOB switching

JOB range of the function torches (MT PC2, PM 2U/D, PM RD2)

Upper limit: 169 (ex works)

P16

0-1

JOB batch mode

0 =-------- Block JOB mode not enabled (ex works)

1 =-------- Block JOB mode enabled

P17

0-1

Program selection with standard torch trigger

0 =-------- No program selection (ex works)

1 =-------- Program selection possible

P23

0-1

Program settings for relative programs

0 =-------- Combined setting of relative programs possible (ex works).

1 =-------- Individual setting of relative programs possible.

Содержание Expert XQ 2.0





























































































Результаты поиска

Содержание Expert XQ 2.0

Отзывы:

Похожие инструкции для Expert XQ 2.0

Бренды по названию

Популярные бренды

EWM Expert XQ 2.0, Руководство по эксплуатации

Результаты поиска

Содержание Expert XQ 2.0

Отзывы:

Похожие инструкции для Expert XQ 2.0

Бренды по названию

Популярные бренды