ETOP P/I-P3BVL Скачать руководство пользователя | Manualshive

Страница: 61 / 68

background image

Chapter 3 BIOS Configuration

P/I-P3BVL User's Manual 55

On-Chip Primary/Secondary PCI IDE

The integrated peripheral controller contains an IDE interface with
support for two IDE channels. Select

Enabled

to activate each channel

separately.

USB Keyboard Support

Select

Enabled

if your system contains a Universal Serial Bus (USB)

controller and you have a USB keyboard.

Init Display First

This field allows the system to initialize the first VGA card on the PCI
slot of the back-plane when system is turned on. The default is the
on-board ATI AGP VGA.

Onboard FDC Controller

Select

Enabled

if your system has a floppy disk controller (FDC)

installed on the SBC card and you wish to use it. If you install an
add-in FDC or the system has no floppy drive, select Disabled in this
field. This option allows you to select the onboard FDD port.

Onboard Serial/Parallel Port

These fields allow you to select the onboard serial and parallel ports
and their addresses. The default value for these ports are:
Serial Port 1  3F8/IRQ4
Serial Port 2  2F8/IRQ3
Parallel Port  378H/IRQ7

UART Mode Select

This field determines the UART mode in your computer. The settings
are

Normal, IrDA and ASKIR

. The default value is

Normal

.

Parallel Port Mode

This field allows you to determine parallel port mode function.
SPP   Normal Printer Port
EPP   Enhanced Parallel Port
ECP  Extended Capabilities Port

«
...
59
60
61
62
63
...
»

Содержание P/I-P3BVL





































































Отзывы:

Нет отзывов

Похожие инструкции для P/I-P3BVL

1stMainboard VG33

Бренд: FIC Страницы: 38

Бренд: Texas Instruments Страницы: 47

STEVAL-IME008V1

Бренд: STMicroelectronics Страницы: 19

Бренд: Nuvoton Страницы: 14

Бренд: ON Semiconductor Страницы: 19

Бренд: MINN KOTA Страницы: 16

Бренд: Advantech Страницы: 4

Бренд: Octek Страницы: 102

Бренд: ON Semiconductor Страницы: 3

Бренд: K&B Страницы: 6

BOOSTXL-DRV8301

Бренд: Texas Instruments Страницы: 13

Supero X9DRW-7TPF

Бренд: Supero Страницы: 119

Бренд: LiteOn Страницы: 38

Бренд: C-Control Страницы: 8

Бренд: Global American Страницы: 31

Z80 Super Bullet

Бренд: Wave Mate Страницы: 25

Kontron mITX-VR1000 V2.0

Бренд: S&T Страницы: 8

Бренд: TYAN Страницы: 86

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды