ETOP P/I-P3BVL Скачать руководство пользователя страница 60 | Manualshive

Страница: 60 / 68

background image

Chapter 3 BIOS Configuration

54 P/I-P3BVL User's Manual

Integrated Peripherals

This option sets your hard disk configuration, mode and port.

ROM PCI/ISA BIOS

INTEGRATED PERIPHERALSP

AWARD SOFTWARE INC.

IDE HDD Block Mode

: Enabled

Onboard Serial Port 1

: 3F8/IRQ4

IDE Primary Master PIO

: Auto

Onboard Serial Port 2

:

3F8/IRQ4

IDE Primary Slave PIO

: Auto

UART Mode Select

: Normal

IDE Secondary Master PIO

: Auto

IDE Secondary Slave PIO

: Auto

IDE Primary Master UDMA

: Auto

Onboard Parallel Port

: 378/IRQ7

IDE Primary Slave UDMA

: Auto

Parallel Port Mode

: SPP

IDE Secondary Master UDMA

: Auto

IDE Secondary Slave UDMA

: Auto

On-Chip Primary PCI IDE

: Enabled

On-Chip Secondary PCI IDE

: Enabled

USB Keyboard Support

: Disabled

Init Display

First

: PCI SLOT

Onboard FDC Controller

: Enabled

ESC : Quit

↑

↓

→

←

: Select Item

F1 : Help

PU/PD/+/- : Modify

F5 : Old Values

(Shift) F2 : Color

F6 : Load BIOS Defaults

F7 : Load Setup Defaults

IDE HDD Block Mode

This field allows your hard disk controller to use the fast block mode to
transfer data to and from your hard disk drive.

IDE Primary/Secondary Master/Slave PIO

These fields allow your system hard disk controller to work faster.
Rather than have the BIOS issue a series of commands that transfer to
or from the disk drive, PIO (Programmed Input/Output) allows the
BIOS to communicate with the controller and CPU directly.

The system supports five modes, numbered from 0 (default) to 4, which
primarily differ in timing. When Auto is selected, the BIOS will select
the best available mode.

IDE Primary/Secondary Master/Slave UDMA

These fields allow your system to improve disk I/O throughput to
33Mb/sec with the Ultra DMA/33 feature. The options are

Auto

and

Disabled

.

«
...
58
59
60
61
62
...
»

Содержание P/I-P3BVL





































































Отзывы:

Нет отзывов

Похожие инструкции для P/I-P3BVL

Бренд: Yamaha Страницы: 83

Бренд: IEI Technology Страницы: 211

Бренд: IEI Technology Страницы: 8

Бренд: IEI Technology Страницы: 8

Бренд: Phytec Страницы: 128

Бренд: Sapphire Audio Страницы: 50

Бренд: JETWAY Страницы: 49

H470 AORUS PRO AX

Бренд: Gigabyte Страницы: 52

Бренд: BCM Страницы: 57

Бренд: Peak Страницы: 33

Бренд: SOLTEK Страницы: 94

Бренд: Advantech Страницы: 34

Бренд: Advantech Страницы: 46

Бренд: Texas Instruments Страницы: 25

Бренд: Strontech Страницы: 35

Бренд: TYAN Страницы: 83

Бренд: Biostar Страницы: 31

Бренд: Biostar Страницы: 59

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды