ETOP P/I-P3BVL Скачать руководство пользователя | Manualshive

Страница: 47 / 68

background image

Chapter 3 BIOS Configuration

P/I-P3BVL User's Manual 41

NOTE

: The specifications of your drive must match with the drive

table. The hard disk will not work properly if you enter
incorrect information in these fields. If your hard disk drive
type is not matched or listed, you can use Type User to
define your own drive type manually.

Drive A / Drive B

These fields identify the types of floppy disk drive A or drive B that
has been installed in the computer. The available specifications are:

360KB

5.25 in.

1.

2MB

5.25 in.

720KB

3.5 in.

1.

44MB

3.5 in.

2.

88MB

3.5 in.

Video

This field selects the type of video display card installed in your system.
You can choose the following video display cards:
EGA/VGA  For EGA, VGA, SEGA, SVGA
      or PGA monitor adapters. (default)
CGA 40 Power up in 40 column mode.
CGA 80 Power up in 80 column mode.
M O N O   For Hercules or MDA adapters.

Halt On

This field determines whether the system will halt if an error is detected
during power up.
No errors

The system boot will not be halted for any
error that may be detected. (default)

All errors

Whenever the BIOS detects a non-fatal error,
the system will stop and you will be
prompted.

All, But Keyboard

The system boot will not be halted for a
keyboard error; it will stop for all other errors

All, But Diskette

The system boot will not be halted for a disk
error; it will stop for all other errors.

All, But Disk/Key

The system boot will not be halted for a key-
board or disk error; it will stop for all others.

«
...
45
46
47
48
49
...
»

Содержание P/I-P3BVL





































































Отзывы:

Нет отзывов

Похожие инструкции для P/I-P3BVL

Бренд: Biostar Страницы: 45

Бренд: AOpen Страницы: 8

Бренд: Intel Страницы: 76

B85 Anniversary

Бренд: ASROCK Страницы: 148

Бренд: JETWAY Страницы: 58

Бренд: MSI Страницы: 96

Бренд: Aaeon Страницы: 120

Бренд: ASROCK Страницы: 154

Z690M DS3H DDR4

Бренд: Gigabyte Страницы: 36

MAG Z490 TOMAHAWK

Бренд: MSI Страницы: 76

Бренд: ECS Страницы: 64

Бренд: Supero Страницы: 77

Бренд: Supermicro Страницы: 147

Бренд: Supero Страницы: 80

Бренд: Supermicro Страницы: 126

WAFER-BW-N4-R10

Бренд: IEI Technology Страницы: 136

Бренд: Intel Страницы: 91

Бренд: Gigabyte Страницы: 113

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды