ETOP P/I-P3BVL Скачать руководство пользователя | Manualshive

Страница: 43 / 68

background image

Chapter 3 BIOS Configuration

P/I-P3BVL User's Manual 37

BIOS Introduction

The Award BIOS (Basic Input/Output System) installed in your
computer system's ROM supports Intel Pentium II/III processors in a
standard IBM-AT compatible I/O system. The BIOS provides critical
low-level support for standard devices such as disk drives, serial and
parallel ports. It also adds virus and password protection as well as
special support for fine-tuning of the chipset to control the entire
system.

BIOS Setup

The Award BIOS provides a Setup utility program for specifying the
system configurations and settings. The BIOS ROM of the system
stores the Setup utility. When you turn on the computer, the Award
BIOS is immediately activated. Pressing the <Del> key immediately
allows you to enter the Setup utility. If you are a little bit late pressing
the <Del> key, POST(Power On Self Test) will continue with its test
routines, thus preventing you from invoking the Setup. If you still wish
to enter Setup, restart the system by pressing the "Reset" button or
simultaneously pressing the <Ctrl>, <Alt> and <Delete> keys. You can
also restart by turning the system Off and back On again. The
following message will appear on the screen:

Press <DEL> to Enter Setup

In general, you press the arrow keys to highlight items, <Enter> to
select, the <PgUp> and <PgDn> keys to change entries, <F1> for help
and <Esc> to quit.

When you enter the Setup utility, the Main Menu screen will appear on
the screen. The Main Menu allows you to select from various setup
functions and exit choices.

«
...
41
42
43
44
45
...
»

Содержание P/I-P3BVL





































































Отзывы:

Нет отзывов

Похожие инструкции для P/I-P3BVL

Бренд: ASROCK Страницы: 126

Бренд: AOpen Страницы: 8

Бренд: Texas Instruments Страницы: 19

ML501MicroBlaze

Бренд: Xilinx Страницы: 46

Бренд: Ublox Страницы: 38

Бренд: Supermicro Страницы: 91

Бренд: Texas Instruments Страницы: 54

A320M-K PRO V14

Бренд: Colorful Страницы: 12

Бренд: Unicorn Computer Страницы: 36

Бренд: ECS Страницы: 74

Бренд: ASROCK Страницы: 43

DisplayPort VIP Input Board

Бренд: Lattice Страницы: 21

Бренд: Gigabyte Страницы: 96

Бренд: JETWAY Страницы: 60

Бренд: Apex Digital Страницы: 7

Бренд: Pentium Страницы: 48

Бренд: BCM Advanced Research Страницы: 72

Бренд: ASROCK Страницы: 39

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды