ETAS ES5340.2 Скачать руководство пользователя страница 4

Страница: 4 / 120

ES5340.2 Electric Drive Simulation Board - User’s Guide

Contents

ETAS

2.2.1

Connecting Master and Slave via Gigabit Link . . . . . . . . . . . . . . . . 25

2.2.2

Configuration in LABCAR-RTC. . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

2.3

RPM Master/Slave Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
2.3.1

Connecting the RPM Buses of Two Boards. . . . . . . . . . . . . . . . . . . 26

2.3.2

Configuration of the RPM Unit (in LABCAR-RTC) . . . . . . . . . . . . . . 27

2.4

“Exclusive Core Usage” Mode . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

3 Hardware Description . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

3.1

Generating Analog Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32
3.1.1

Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32

3.1.2

Configuring the Analog Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . 33

3.2

Output Multiplexers for the Analog Signals . . . . . . . . . . . . . . . . . . . . . . . . . 36

3.3

Generating Digital Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38
3.3.1

Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 38

3.3.2

Configuring the Digital Signals . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

3.4

Output Multiplexers for the Digital Signals . . . . . . . . . . . . . . . . . . . . . . . . . 41

3.5

Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.5.1

Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

3.5.2

Configuring the Analog Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

3.6

Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42
3.6.1

Specification . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 42

3.6.2

Configuring the Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . 43

3.6.3

Configuration with ES5436.1 to Measure ECU Digital Output Signals
44

3.6.4

Configuration as H-Bridge . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 46

3.7

RPM Generator . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47
3.7.1

Angle Clock Signal . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

3.7.2

Synchronization. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

3.7.3

"Master with Angle Adaptation" RPM Mode. . . . . . . . . . . . . . . . . 48

4 FPGA Models . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 49

4.1

Permanent Magnet Synchronous Machine (PMSM) Model . . . . . . . . . . . . . 49
4.1.1

Inverter – Parameters, Inputs and Outputs . . . . . . . . . . . . . . . . . . . 51

4.1.2

PMSM – Parameters, Inputs and Outputs. . . . . . . . . . . . . . . . . . . . 55

4.1.3

Mechanical System – Parameters, Inputs and Outputs . . . . . . . . . . 57

4.2

Induction Machine (IM) Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 59
4.2.1

Inverter – Parameters, Inputs and Outputs . . . . . . . . . . . . . . . . . . . 60

4.2.2

Induction Machine – Parameters, Inputs and Outputs . . . . . . . . . . 62

4.2.3

Mechanical System – Parameters, Inputs and Outputs . . . . . . . . . . 63

5 Configuring the Hardware in LABCAR-RTC . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

5.1

General Settings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66
5.1.1

"ES5340-Master" item . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 66

5.1.2

Measuring the Gate Trigger Signals . . . . . . . . . . . . . . . . . . . . . . . . 67

5.1.3

RPM Unit. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 69

5.2

Integration of the Model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71
5.2.1

FPGA model . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

5.2.2

Software Model. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 75

5.3

I/O Configuration . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81
5.3.1

Position sensors . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Содержание ES5340.2

























































































































Результаты поиска

Содержание ES5340.2

Отзывы:

Похожие инструкции для ES5340.2

Бренды по названию

Популярные бренды

ETAS ES5340.2, Руководство пользователя

Результаты поиска

Содержание ES5340.2

Отзывы:

Похожие инструкции для ES5340.2

Бренды по названию

Популярные бренды