ETAS ES5340.2 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 120

background image

ES5340.2 Electric Drive Simulation Board - User’s Guide

16

Introduction

ETAS

Requirements for the Installation Location

Requirements for Ventilation

Transport and Installation

Connecting/Disconnecting Devices

To avoid injuries and hardware damages, please observe the following precau-
tionary measures:

• Do not apply any voltages to the connections of the product that do not

correspond to the specifications of the respective connection.

• Do not connect or disconnect any devices while the ES5300.1-A Housing,

the ES5300.1-B Housing or connected devices are switched on. First,
switch off the ES5300.1-A Housing and the ES5300.1-B Housing by shut-
ting down the real-time PC and by pressing the On/Off switch at the rear,
then unplug the power cable.

• When plugging in connectors, ensure that they are inserted straight and

no pins are bent.

WARNING!

This is class A equipment. This equipment can cause radio interfer-
ence in residential areas. Should that be the case, the operator may
be requested to institute reasonable measures.

CAUTION!

The air circulation inside the ES5300.1-A Housing and the ES5300.1-
B Housing can only be maintained if all free slots are covered with
front plates. Otherwise, it may lead to overtemperatures and trip the
overtemperature protection of the ES5300.1-A or the ES5300.1-B.
For this reason, install front plates in all free slots!

CAUTION!

Some components of the product can be damaged or destroyed by
electrostatic discharges. Leave the plug-in board in its transport pack-
aging until it is installed.
Only remove, configure and install the product at a workplace that is
protected against electrostatic discharges.

CAUTION!

In order to prevent damage to the plug-in boards and the LABCAR
Housing, and thereby also avoid damage to property or health,
observe the installation instructions and information contained in the
relevant User's Guides.

«
...
14
15
16
17
18
...
»

Содержание ES5340.2

























































































































Отзывы:

Нет отзывов

Похожие инструкции для ES5340.2

Бренд: Ubiquiti Страницы: 24

Бренд: GE Страницы: 93

Бренд: Patton electronics Страницы: 51

Z3-DM8168-PCI-RPS

Бренд: Z3 Technology Страницы: 20

Z3-DM8107-SDI2-RPS

Бренд: Z3 Technology Страницы: 75

Бренд: Z-Wave Страницы: 13

LightSpeed Appliance QLS250

Бренд: Quantum Страницы: 12

Бренд: SUNRICH TECHNOLOGY Страницы: 5

Бренд: Baldor Страницы: 34

ST62GP-EMU2 HDS2 Series

Бренд: STMicroelectronics Страницы: 58

Бренд: EVOC Страницы: 57

Бренд: A2B Electronics Страницы: 24

Бренд: ZALMAN Страницы: 6

PROM Programming Adapters PCA7438F-64A

Бренд: Renesas Страницы: 18

Бренд: Rane Страницы: 6

Бренд: Rajant Страницы: 93

Бренд: H3C Страницы: 62

Бренд: B&B Electronics Страницы: 74

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды