esera automation 1-Wire Controller 2 Скачать руководство пользователя | Manualshive

Страница: 58 / 77

background image

All rights reserved. Reproduction as well as electronic duplication of this guide, complete or in part, requires the written consent of ESERA-
Automation or E-Service GmbH. Errors and technical modification subject to change.

©

ESERA-Automation, E-Service GmbH 2019

www.esera.de

Programming Manual Controller-Gateway-Station V1.0 R1.1

Page 58 of 77

18.4.

Output analog value 0-20mA, 1-Wire actuator

The 0-20mA module is not yet available at the time of creation of this document.
Via the ESERA-Automation module "Analog output 0-20mA" (Art. No. 11219) you can output analog values in the
range of 0-10V with a resolution of 39.2mV (8 bit, 255 levels).

Command: SET,OWD,OUTAMA,OWD-number,output current

Example: set,owd,outama,2,1000 => OWD number 2, output current is 10mA.
After controlling the module, the new status is output as confirmation.

18.5.

Output PWM output, 1-Wire actuator

Via the ESERA module "PWM output 10V" (Art. No. 11225) you can output analog values in the range of 0-100%
with an output voltage of 10V and 2kHz with a resolution of 1% (8 bit, 255 levels).

Command: SET,OWD,OUTPWM,OWD-number,PWM-value

Example: set,owd,outama,2,50 => OWD number 2, PWM signal with 50 % pulse-pause ratio.
After controlling the module, the new status is output as confirmation.

18.6.

1-Wire dimmer control, Art. No. 11221, 11222, 11224

There is a special control command for ESERA dimmer modules to control outputs and the dimming value in
levels 0-31. With this command the entire 1-Wire control between the 1-Wire Controller / 1-Wire Gateway and the
1-Wire dimmer is taken over.

Command: SET,OWD,DIM,OWD-number,output,dimming value
Note

: There are several 1-Wire dimmers in development at ESERA-Automation. Please refer to the ESERA-

Automation Online Shop for availability of the respective modules.

18.7.

Roller shutter control, 1-Wire Shutter Art. No. 11209, 11231

For ESERA shutter modules (Art. No. 11209 V2 and V3, 11231) there are special commands for controlling the
travel-direction of roller shutters or awnings. With this command setting and resetting of the outputs of the
DS2413 device is no longer necessary.
The following functions are available: 1=Down, 2=Up and 3=Stop

Command: SET,OWD,SHT,OWD-number,function

After switching the output, the new status is output as confirmation.

Via the Config-Tool 3 you can directly control different 1-Wire modules.
Please refer to the chart below for the control of an 8-fold digital output module.

a. Select an OWD-module from the list.
b. If an article number has been assigned for

this module, adapted functions are
activated. In this example push button with
status display is activated.

c. In addition, the output ASCII values for the

module are displayed.

a.

b.

c.

c.

«
...
56
57
58
59
60
...
»

Содержание 1-Wire Controller 2














































































Отзывы:

Нет отзывов

Похожие инструкции для 1-Wire Controller 2

Бренд: 3idee Страницы: 7

Бренд: 3idee Страницы: 6

Бренд: Zenisu Keisoku,Inc. Страницы: 21

Бренд: Becker Страницы: 4

Бренд: Flexport Страницы: 17

Бренд: Hama Страницы: 74

Бренд: Aaronn Страницы: 2

Бренд: Logitech Страницы: 143

Бренд: Asante Страницы: 2

Бренд: Roving Networks Страницы: 8

Бренд: Adaptec Страницы: 50

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

MHC-EC78Pi - Mini Hi-fi Component System

Бренд: Sony Страницы: 2

MHC-EC78Pi - Mini Hi-fi Component System

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренд: Sony Страницы: 2

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды