Escea AF series Скачать руководство пользователя страница 49

Страница: 49 / 58

SER

VICE

G6 Inroom Horizontal Flue Kit

For horizontal termination the following are dimensions for installing the Inroom Horizontal ﬂue kit.
Note: Instructions for installation are provided with the kit

G7 AF700 Fireplace installation into FS730 Freestanding Unit

Once the freestanding unit is in place, and the ﬂue system installed, the AF700
ﬁreplace installation can commence.

Note:

for the Apartment Flue Kit, see the instructions provided with the kit.

Place the freestanding unit in the correct location, complying with the

clearances speciﬁed in the previous section.

Remove 2 screws on each side of the fascia just below the top panel and pull

towards you to remove the fascia.

Refer to section C of this installation manual for minimum and maximum ﬂue

lengths, restrictor settings for your installation, and all other ﬂue information.

Prepare the ﬂue for ﬁre installation, by sliding the ﬂexible ﬂues down the liner

and attaching to the ﬂue spigot plate as per the end of section C

Take the plastic grommet in the back panel out. Push the power cable through

the hole in the rear, then push the grommet over the power cable and ﬁx the
grommet back to the back panel.

Install the AF700 ﬁreplace into the freestanding unit while sliding on the ﬂue

spigot plate as per section E.

Run gas piping to the front right of the ﬁreplace as shown, where you will ﬁnd

a hole positioned so the gas pipe can run directly to the regulator and be connect-
ed as per section E.

Содержание AF series



























































Результаты поиска

Содержание AF series

Отзывы:

Escea AF series, Инструкция по установке и обслуживанию, Страница: 49 / 58

Результаты поиска

Содержание AF series

Отзывы: