manualshive.com logo in svg

Escea AF series, Инструкция по установке и обслуживанию, Страница: 11 / 58

Поделиться
Скачать
Escea AF series Скачать руководство пользователя страница 11

B

A

C

D

E

F

G

SER

VICE

11

Masonry Installation Requirements

The masonry install requires a spacer below the appliance to allow room for the fascia to sit flush with 
the ground.

B2 Floor 

Clearances

If the appliance is mounted above a “hard floor” (including but not necessarily limited to: wood, wood 
veneers, ceramic tiles, concrete and stone) then it may be positioned with the bottom of the fascia 
coincident with the finished floor if desired.  Note: The appliance has been tested and certified to 
AS4553:2008 and the maximum allowable temperature rise above ambient of any combustible floor 
is ΔT of 65C. Therefore any material used must be chosen to be able to operate without damage or 
degradation with a ΔT of 65C.
If the appliance is mounted above a “Soft floor” ” (including but not necessarily limited to: carpets, 
Vinyl, carpet tiles, rugs and mats) then we recommend a distance of 100mm from the bottom of the 
fascia to the finished floor.
Refer to section B4 for hearths.

B3  Flexi Flue & Converter Box Clearances

25mm

=

 Minimum distance to combustibles

50mm

50mm

0mm*

*

Note: Underside of converter box can be fixed straight onto wooden joists.

**

Note: Flexi-Flue must not be run at an angle greater than 45 degrees from 

vertical; excluding all appliance built into a freestander kit.

50mm

50mm

>45°**

50mm

Ø75mm I

ntake 

Ø100mm Exhaust 

50mm

25mm

25mm

 600mm

 300mm t

o

Содержание AF series



























































Отзывы:

Нет отзывов