Escea AF series Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 58

Escea AF series Скачать руководство пользователя страница 37

B

A

C

D

E

F

G

SER

VICE

37

E6 Connecting the Gas Pipe to the Regulator

Note: The regulator that is supplied with the ﬁre MUST NOT BE REMOVED. Removal of the regulator, or
replacing it with one not intended for use with an Escea ﬁre, will void the limited appliance warranty.

The gas connection on the appliance regulator is a ½” female BSPP at the front right of the appliance;
the regulator is located on the underside of the main burner tray (circled below). The gas supply sec-
tion of the piping will need to be ﬂexible inside the chassis to allow for pipe disconnection and burner
tray removal.
With the burner tray out, the ﬂexible gas supply pipe may be bent into position to align with the regu-
lator connection point when the burner tray is replaced.
The gas supply can be tightened onto the regulator through the access hatch shaded in the diagram
below.

E7 Gas Isolating Valve

It is recommended that a gas isolating valve be installed as close to the regulator on the gas inlet side as
possible with easy access if the fascia is removed. This will allow for easier servicing in the future.

E8 Pressure Test Point

As per AS/NZS 5601, a pressure test point shall be provided by the installer prior to the inlet of the
appliance.

«
...
35
36
37
38
39
...
»

Содержание AF series



























































Отзывы:

Нет отзывов