manualshive.com logo in svg

Ericsson FSU 995 F, Руководство пользователя, Страница: 76 / 86

Поделиться
Скачать
Ericsson FSU 995 F Скачать руководство пользователя страница 76

74

Appendix B - Technical data

Appendix B - Technical data

FSU 995 FA Technical data

Fibers

Single fiber with a cladding diameter:

30 - 270 

m

m in Automode (automatic alignment)

30 - 400 

m

m in Manual mode (manual alignment)

Single fiber with coating diameter up to 2000 

m

m

Special single fibers including erbium, dispersion shifted and multimode

Splice loss

Typical value using identical single mode fibers: 0.02 dB

Fiber clamping

On bare fiber with blue V-grooves
On primary coating with black V-grooves

Power supply

90 - 264 V AC, 50 - 60 Hz
13.2 V DC

Battery

Splicer only: greater than 100 splices per charge
Splicer and heat oven: greater than 50 splices per charge
Recharging time: 10 hours

Operating environment

0 - 40

o

C, 0 - 95% RH (non-condensing)

Storage environment

-40 - 60

o

C, 0 - 95% RH (non-condensing)

Monitor

3” high-resolution LCD monitor

Video output

1 V p-p positive, 75 ohms/CCIR

Size

37 x 22 x 14.5 cm (W x D x H)
(approx. 14.6 x 8.7 x 5.7 in)

Weight

6.45 kg (without power supply)
(approx. 14.2 lbs.)

Transport casing

Rugged cabin-sized case with space for all necessary accessories
(54.5 x 42.5 x 25.5 cm (approx. 21.5 x 16.7 x 10 in) W x D x H, upright)

AUX-connector pin description

1

Power ground

2

Not used

3

Not used

4

Not used

5

Not used

6

Disable FSU 995 FA OFF-button (active low)
(To prevent external units from losing power
when using internal power from FSU 995 FA)

7

Optional

8

Not used

9

Power: +12 V DC, Fuse 2A

The AUX-connector is intended for external units
such as a larger monitor.

RS 232  pin description

1

Power ground

2

T x D (Transmit data)

3

R x D (Receive data)

4

RTS (Request to send)

5

To CPU-board (No function)

6

To CPU-board (EXTM-signal)

7

Not used

8

CTS (+12 V, pull-up 1 ko)

9

Power: +12 V DC, Fuse 2A

The RS 232 is intended for serial communication
with a PC or printer.

Содержание FSU 995 F























































































Отзывы:

Нет отзывов