Ericsson FSU 995 F Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 86

Ericsson FSU 995 F Скачать руководство пользователя страница 47

45

ADVANCED OPERATION - Program editing

OVERWRITE P

xx

?

“

“

Confirm wish to over-
write parameters

Yes

The splicer will then ask you to confirm that you want to re-
place the parameters in the program selected in step 1 with
those of the source program just selected. This confirmation
is very similar to what computers do when they ask you if you
are sure you want to delete a certain file, because copying the
source program’s parameters will erase whatever parameters
were there beforehand.

To confirm your desire to copy the source program, press Yes .
If you press No, then the copying will be cancelled.

As a last precaution, the splicer will then ask for the security
code for the source program if the source program is classi-
fied as “Confidential”. This is to ensure that no one has ac-
cess to programs they shouldn’t just by copying them to a
new slot. To give a source program’s security code, you follow
the same procedure as in step 3.

Pass through security

on source program

See step 3

Use another program as a base

4

As has been recommended earlier, it is helpful to use another
program as a base when designing your own. If you want to
do so, and copy the parameters of another program into the
slots of your new program, you should press Yes at this point.
If you do not want to copy parameters from another program-
-because you are editing again a program you designed
previously, for example--you should press No and go onto
step 5 on the following page.

The splicer will then ask in the

message field

which program

you want to copy (“Copy Source P

yy

”), and you must enter

the number of the program you want to copy by using the
first two number buttons (from the left). Let’s say that we
chose to copy the parameters from Program 08. In that case
you would enter a “0” with the first number button and an “8”
with the second.

You enter the choice of source program by pressing ENTER.

COPY PARAMETERS?

“

“

0-9

0-9

Type in source program
number

Confirm wish to copy

COPY SOURCE P

yy

“

“

Enter

Enter source program

Yes

«
...
45
46
47
48
49
...
»

Содержание FSU 995 F























































































Отзывы:

Нет отзывов