manualshive.com logo in svg

Ericsson FSU 995 F, Руководство пользователя, Страница: 64 / 86

Поделиться
Скачать
Ericsson FSU 995 F Скачать руководство пользователя страница 64

62

ADVANCED OPERATION - Special functions: Global parameters

Table of contents

Parameter

Function

Range

Default

LOSS EST. LEV

Gives you the option of deciding

0 to 2

2

in what cases you want the splicer
to estimate the splice loss.
0 = No  loss estimation
1 = Estimation only when in Automode
2 = Always do loss estimation

SHOW LOSS TO

When the estimated loss exceeds

0.0 to 49.9 dB

2.0 dB

this value the splicer will display
“BAD SPLICE.”

MACROBENDING

A proportionalizing factor that is

0.0 to 9.9

0.3

used to optimize estimation of
loss due to macrobending.

AUTOXCT OFFSET

Gives the offset to the set splicing

-90 to +90 pixels

0 pixels

position (see also 

AUTO ARC

CENTER

 on p. 56).

GLOBAL XCT

Allows you to change the splicing

150 to 360 pixels

255 pixels

position (see also SET CENTER
POSITION  on p.55)

WEIGHT FACTOR

A factor that sets the grade of

0.00 to 0.99

0.25

impact for measured data in the

(0.00 = low

equation used by the 

Automatic

 0.99 = high)

Arc Re-centering

 function.

RTC CURR LOL

Low limit for RTC current.

0 to 29.9 mA

14.5 mA

RTC CURR HIL

High limit for RTC current.

0 to 29.9 mA

15.5 mA

SPLICES TOTAL:

The total number of splices made

0 to 

x

x

by the splicer: UNEDITABLE.

SPLICES:

Splice counter.

0 to 

x

x

RESET SPLICES?

Resets splice counter to 0.  Use

YES/NO

NO (=0)

after you have replaced electrodes.

WAIT TIME

Time of inaction before splicer

0.0 to 4.9 MN

1.0 MN

turns off automatically.

ELECTROD WARNING

Number of splices before splicer

00 to 99 HS

20 HS

warns you that it is time to

(HS = hundred

(=2000 splices)

replace the electrodes.

splices)

TURN OFF

Enable/Disable the function that

YES/NO

YES (=1)

automatically turns off the splicer

YEAR

The current year.

00 to 99

set in factory

MONTH

The current month.

00 to 12

set in factory

DAY

The current day.

00 to 31

set in factory

HOUR

The current hour.

00 to 24

set in factory

MIN

The current minute.

00 to 59

set in factory

Estimation parameters

Current

CPU settings

O

ffset parameters

Содержание FSU 995 F























































































Отзывы:

Нет отзывов