Ericsson FSU 995 F Скачать руководство пользователя страница 37 | Manualshive

Страница: 37 / 86

Ericsson FSU 995 F Скачать руководство пользователя страница 37

35

ADVANCED OPERATION - Splicing program structure: Splicing process

Pulling or tapering

Pre-defined program: 09

Pulling or tapering is used primarily to create micro-lenses
and microscope fiber probes out of fiber end-faces. During
the process, the splicer simultaneously pulls and heats the
fibers into an hour glass shape that eventually divides at the
tip. This tapering process increases the mode field diameter
to give the fiber a higher numerical aperture. To then capital-
ize on this phenomenon to make a micro-lens, the ends are
made to take on a semi-spherical form which can focus light
from an external source into the core.

Example of fiber probes for a micro-

scope

Hour-glass form at the end of the first

pulling step using Program 09

Pulling or tapering control parameters

PULL 1, PULL 2, PULL 3

are the three parameters controlling the pulling or tapering
process. They represent three rounds of pulling, and each is
associated with the FUSION CURRENT and FUSION TIME
carrying the same number (eg. FUSION CURRENT 2 is the
current used during PULL 2). The PULL parameters are
binary and can only be turned off or on.

Example of micro-lenses formed using

Program 09

Sample program for creating fiber probes

FUSION CURRENT 1

12 mA

FUSION TIME 1

15 sec.

PULL 1

Yes

FUSION CURRENT 2

10 mA

FUSION TIME 2

5 sec.

PULL 2

Yes

FUSION CURRENT 3

7 mA

FUSION TIME 3

10 sec.

PULL 3

Yes

«
...
35
36
37
38
39
...
»

Содержание FSU 995 F























































































Отзывы:

Нет отзывов