Ericsson FSU 995 F Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 86

Ericsson FSU 995 F Скачать руководство пользователя страница 46

44

Enter editing mode

2

Enter

Start program editing

NEW PROGRAM?

“

“

Regardless of whether you have just gone through the pro-
gram selection procedure, or are starting program editing
here, you press ENTER to enter editing mode. (It is equiva-
lent to step D in the program selection procedure.) The
splicer will then ask you (possibly for the second time) if you
want to change program.

If the program listed in the

mode field

is indeed the one you

want to edit, you should answer No , and reject program
selection.

No

Reject program selection

Program to edit in mode field

Yes

Confirm editing

EDIT PARAMETERS?

“

“

The splicer will then ask if you want to edit parameters, and
you confirm this by pressing Yes . At this point you will enter
program editing mode.

If you answer No, you will exit both program editing and
program selection, and will return to splicing mode.

Pass through security

3

If the program you have selected in step 1 is classified as an
“Open” program, you will not be asked to enter a key number
(a security code).

If, however, the selected program is classified as either “Read
only” or “Confidential,” you must enter the security code at
this point using the number buttons. Remember that the
number buttons are organized such that the first button (from
the left) corresponds to the first number of the code, the
second button to the second number, and the third to the
third.
You will then have to confirm the code by pressing ENTER. If
you have entered the wrong code, you will be aborted from
program editing.

KEY NUMBER

xx.x

“

“

0-9

0-9

0-9

Type in security code

Enter

Enter code

ADVANCED OPERATION - Program editing

«
...
44
45
46
47
48
...
»

Содержание FSU 995 F























































































Отзывы:

Нет отзывов