Enviro E33GI Скачать руководство пользователя

Страница: 28 / 41

Initial Installation

QUALIFIED INSTALLERS ONLY

ine

onnection

WARNING: Only persons licensed to work with gas piping

may make the necessary gas connections to this

appliance.

Gas Line Connection:

• A ⅜” 45° flared fitting and flex connector are supplied with

the unit (see Figures 36 and 37). Consult the local authorities

for local codes or use the CAN/CGA B149 (1 or 2) installation

code in Canada. In the US, gas installations follow either local

codes or the current edition of the National Fuel Gas Code

ANSI Z223.1.

• If the factory-built fireplace has no gas access hole(s)

provided, an access hole of 1.5 in (37.5mm) or less may be

drilled through the lower sides or bottom of the firebox in a

proper workmanship like manner. This access hole must be

plugged with non-combustible insulation after the gas supply

line has been installed.

•

A shut-off valve is supplied with this unit.

• The appliance and its shut-off valves must be disconnected

from the gas supply piping system during any pressure testing

where the pressure exceeds ½ psig (3.45 KPa) or the valve

will be damaged.

Figure 36: Gas connection location

Figure 37: Gas valve with

cover removed

Table 7: Orifice and Pressure Information.

E33GI / E33GID with Glass Burner

Main Burner

Natural Gas

Propane Gas

Orifice:

#41 DMS

#54 DMS

Max. Manifold Press:

3.8 W.C. (0.95 KPa)

11.0 W.C. (2.74 KPa)

Min. Manifold Press:

1.2 W.C. (0.30 KPa)

3.7 W.C. (0.92 KPa)

Max. Supply Press:

10.5 W.C. (2.62 KPa)

13.0 W.C. (3.24 KPa

Min. Supply Press:

5.0 W.C. (1.24 KPa)

11.0 W.C. (2.74 KPa)

Max. Input:

31,000 BTU/hr (9.09 KW)

28,000 BTU/hr (8.21 KW)

Min. Input:

17,000 BTU/hr (4.98 KW)

16,500 BTU/hr (4.84 KW)

Содержание E33GI










































Результаты поиска

Содержание E33GI

Отзывы:

Похожие инструкции для E33GI

Бренды по названию

Популярные бренды

Enviro E33GI, Руководство пользователя

Результаты поиска

Содержание E33GI

Отзывы:

Похожие инструкции для E33GI

Бренды по названию

Популярные бренды