Enviro E33GI Скачать руководство пользователя | Manualshive

Страница: 10 / 41

background image

Operating Instructions

10

t

echnicaL

D

ata

Transmitter (Remote Control):

Supply voltage: 4.5 V (three 1.5 V AAA batteries)

Radio frequency: 315 MHz

Integrated Fireplace Controller (IFC):

Supply voltage: AC IN - 120 V / 60 Hz

Battery Backup IN - 6 Vdc - 200mA (four 1.5 V AA batteries)

Spark voltage / frequency: >10kV / 1Hz

Comfort modulating fan: 120 V / 60 Hz / 2A

Auxiliary: 120 V / 60 Hz / 5A

t

RansmitteR

:

The Proflame 2 Transmitter is a remote control with a blue backlit lcd display. It uses a streamline design with

a simple button layout and informative lcd readout (Figure 5). The Transmitter is powered by three (3) AAA

type batteries. A Mode Key is provided to Index between the features and a Thermostat Key is used to turn

on/off or index through Thermostat functions (Figure 5 & 6).

Figure 5: Proflame 2 Transmitter.

s

ystem

D

escRiption

:

The Proflame 2 Remote Control System consists of two (2) elements:

1. Proflame 2 Transmitter.

2. Integrated Fireplace Controller (IFC) and wiring harness to connect to the gas valve, stepper motor

battery holder, and convection fan.

ATTENTION!
- TURN “OFF” THE MAIN GAS SUPPLY OF THE APPLIANCE DURING INSTALLATION OR

MAINTENANCE OF THE IFC.

- TURN “OFF” MAIN GAS SUPPLY TO THE APPLIANCE PRIOR TO REMOVING OR REINSERTING

THE BATTERIES IN THE BATTERY HOLDER

Blue LCD display

UP/DOWN Arrow Key

ON/OFF Key

THERMOSTAT Key

MODE Key

For E33GID models refer to the separate Dexen user

manual supplied for remote control operations.

«
...
8
9
10
11
12
...
»

Содержание E33GI










































Отзывы:

Нет отзывов

Похожие инструкции для E33GI

Бренд: Magiglo Страницы: 48

Бренд: Jøtul Страницы: 104

Бренд: FireplaceXtrordinair Страницы: 38

Бренд: Woodbridge Fireplace Inc Страницы: 48

Бренд: Dimplex Страницы: 8

Бренд: Quality Craft Страницы: 12

Бренд: Majestic Страницы: 40

Бренд: Varde Страницы: 44

Бренд: Napoleon Страницы: 2

Бренд: Saey Страницы: 28

Бренд: Duraflame Страницы: 22

Бренд: Room&Board Страницы: 30

Бренд: FMI Страницы: 40

FP-7-LM ANTOINETTE

Бренд: Valcourt Страницы: 2

Бренд: Valcourt Страницы: 6

Бренд: Style selections Страницы: 17

Бренд: Oblica Страницы: 10

Бренд: Valor Страницы: 3

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды