Enviro E33GI Скачать руководство пользователя

Страница: 18 / 41

ueL

onVeRsion

TO BE INSTALLED BY A QUALIFIED SERVICE AGENCY ONLY

Please read and understand these instructions before installing.

Warning: This conversion kit shall be installed by a qualified service agency in accordance

with the manufacturer’s instructions and all applicable codes and requirements of the

authority having jurisdiction. If the information in these instructions is not followed

exactly, a fire, explosion or production of carbon monoxide may result causing property

damage, personal injury or loss of life. The qualified service agency is responsible for

the proper installation of this kit. The installation is not proper or complete until the

operation of the converted appliance is checked as specified in the manufacturer’s

instructions supplied with the kit.

Kit Parts List for all E33GI models:

1 - Orifice (NG:

#41) or (LP: #54) 1 - Servo Regulator with diaphragm

1 - Installation instruction sheet

2 - Conversion labels

1 - Pilot Orifice (NG: 0.2) or (LP: 0.14)

Carefully inspect all parts supplied with this conversion kit. If any parts have been damaged or are

missing, contact your dealer, distributor or courier company to have them replaced before starting this

installation.

Maintenance And Service

Conversion Kit Installation:

1. Turn the unit off by pressing the ON/OFF Key on the remote and shut off gas supply at the shut-off

valve upstream of the unit. CAUTION: The gas supply must be shut off prior to disconnecting the

electrical power and before proceeding with the conversion. Allow the valve and unit to cool down

to room temperature.

2. Carefully remove the glass media and porcelain tray if they are installed.
3. Remove the burner as shown in the

eConDary

nstallatIon

- f

Irebox

Iner

& b

urner

ray

emoVal

4. Remove the burner as shown in

aIntenanCe

anD

erVICe

- b

urner

emoVal

Figure 23 Proper Pilot Position

6. Convert the burner orifice:

a) Remove the main burner orifice with a

1/2” deep socket

b) Put a bead of pipe-thread sealant into the orifice mount.

DO NOT OVER-TIGHTEN

c) Install new orifice.

5. Convert the pilot orifice:

a) Using a

” wrench, loosen the pilot head counter

clockwise and fully remove

b) Remove the existing orifice and replace with the one

supplied in the kit (see Figure 22)

c) Re-install the pilot head and tighten until it is back in the

proper position (see Figure 23)

Figure 22 Pilot Orifice

Содержание E33GI










































Результаты поиска

Содержание E33GI

Отзывы:

Похожие инструкции для E33GI

Бренды по названию

Популярные бренды

Enviro E33GI, Руководство пользователя

Результаты поиска

Содержание E33GI

Отзывы:

Похожие инструкции для E33GI

Бренды по названию

Популярные бренды