Enviro E33GI Скачать руководство пользователя

Страница: 33 / 41

Secondary Installation

iRebox

ineR

anD

uRneR

Ray

emoVaL

nstaLLation

NOTE: The porcelain on the firebox liners is fragile and should be handled gently.

Ensure the E33GI / E33GID is turned off and allow the unit to completely cool.

2. Remove the glass door as shown in the

aIntenanCe

anD

erVICe

- g

lass

oor

emoVal

WARNING:

Do not touch or attempt to remove the door if the fireplace is not completely cool.

Never operate the fireplace with the door removed.

3. Remove the glass material (if installed).

4. Use the following steps to remove the liners and the burner tray.

NOTE: Follow the steps in the reverse order for reassembly.

WARNING: Failure to position the parts in accordance with these diagrams or failure to use only parts

specifically approved with this appliance may result in property damage or personal injury.

Figure 50:

Remove the side panel retainer clips

which secure the side.i

Figure 49:

Remove the two nuts which hold

down the burner. Gently pull the burner

forward to remove it from the Venturi Box.

Figure 48:

Remove the eight T20 screws and

then remove the glass tray panel by lifting up.

Figure 51:

Remove the side panels then the

back panel.

Содержание E33GI










































Результаты поиска

Содержание E33GI

Отзывы:

Похожие инструкции для E33GI

Бренды по названию

Популярные бренды

Enviro E33GI, Руководство пользователя

Результаты поиска

Содержание E33GI

Отзывы:

Похожие инструкции для E33GI

Бренды по названию

Популярные бренды