Enviro E33GI Скачать руководство пользователя

Страница: 17 / 41

Figure 21: Valve Cover Location

Valve

Cover

Maintenance And Service

Leaning

iRebox

Carefully remove the glass media and porcelain tray. Vacuum the bottom of the firebox thoroughly and

remove any dust/lint from pilot. At this time, inspect the burner tube for cracking or severe warping. If

a problem is suspected, contact the dealer.

epLacing

Lass

The glass in the fireplace is a high temperature ceramic. If the glass is damaged in any way, a factory

replacement is required (see

arts

Ist

). Wear gloves when handling damaged glass door assembly

to prevent personal injury. Do not operate with the glass front removed, cracked or broken. Removal

and replacement of the glass from the door must

be done by a licensed or qualified service person.

The glass must be purchased from an ENVIRO dealer. No substitute materials are allowed.

Remove the door (see page 16). The replacement glass will come with a new gasket installed. Remove

any silicone remnants from the door. Apply high temperature silicone to the two vertical faces of the

door and install the new piece of glass with gasket (be sure to maintain edge clearances). Apply even

pressure to the glass to allow the silicone to adhere to the gasket material.

heck

iLot

anD

uRneR

Lames

Periodically do a visual check of the pilot flames. One flame should encompass the flame sensor (see

page 28) and the other should burn over the burner ports. Also check that the burner is operating

correctly, refer to Venturi Adjustment section.

emoVing

aLVe

oVeR

The valve cover is located on the right side of the cabinet (figure 21) and it can be removed to access the

gas valve. Use a Torx T-20 screwdriver to remove the 6 retaining screws.

Содержание E33GI










































Результаты поиска

Содержание E33GI

Отзывы:

Похожие инструкции для E33GI

Бренды по названию

Популярные бренды

Enviro E33GI, Руководство пользователя

Результаты поиска

Содержание E33GI

Отзывы:

Похожие инструкции для E33GI

Бренды по названию

Популярные бренды