Endress+Hauser Smartec S CLD132 Скачать руководство пользователя страница 4 | Manualshive

Страница: 4 / 44

background image

Basic safety instructions

Smartec S CLD132/134 PROFIBUS-PA/-DP

4

Hauser

1

Basic safety instructions

1.1

Requirements for the personnel

‣

Installation, commissioning, operation and maintenance of the measuring system must
only be carried out by trained technical personnel.

‣

The technical personnel must be authorized by the plant operator to carry out the
specified activities.

‣

The electrical connection may only be performed by an electrical technician.

‣

The technical personnel must have read and understood these Operating Instructions
and must follow the instructions they contain.

‣

Measuring point faults may only be rectified by authorized and specially trained
personnel.

Repairs not described in the enclosed Operating Instructions may only be carried out
directly at the manufacturer's or by the service organization.

1.2

Designated use

These Operating Instructions were designed specifically for use with transmitters of the
family Smartec S CLD132/134. They contain specific information for instruments with the
PROFIBUS PA interface (

Pro

cess

Fi

eld

Bus

-

P

rocess

A

utomation) or the PROFIBUS DP

interface (

Pro

cess

Fi

eld

Bus

-

D

ecentralized

P

eripherals).

PROFIBUS is an open field bus standard according to IEC 61158 / IEC 61784. It has been
created specifically for process control purposes and permits connection of several
measuring instruments to a bus line. The transmission method according to IEC 1158-2
guarantees safe signal transmission.

The PROFIBUS PA interface permits operation of the instrument from the PC:
• via FieldCare (Plant Asset Management Tool)

Any other use than the one described here compromises the safety of persons and the entire
measuring system and is not permitted.
The manufacturer is not liable for damage caused by improper or non-designated use.

1.3

Workplace safety

As the user, you are responsible for complying with the following safety conditions:
• Regulations for explosion protection
• Installation instructions
• Local standards and regulations

Electromagnetic compatibility

With regard to electromagnetic compatibility, this device has been tested in accordance with
the applicable European standards for industrial applications.
The electromagnetic compatibility indicated only applies to a device that has been connected
in accordance with the instructions in these Operating Instructions.

1.4

Operational safety

‣

Before commissioning the entire measuring point, make sure all the connections are
correct. Ensure that electrical cables and hose connections are not damaged.

‣

Do not operate damaged products, and safeguard them to ensure that they are not
operated inadvertently. Mark the damaged product as defective.

‣

If faults cannot be rectified, the products must be taken out of service and secured against
unintentional commissioning.

«
...
2
3
4
5
6
...
»

Содержание Smartec S CLD132













































Отзывы:

Нет отзывов

Похожие инструкции для Smartec S CLD132

Бренд: Keller Страницы: 6

Бренд: Callaway Страницы: 13

Бренд: JAMAR Technologies Страницы: 4

Бренд: Jamar Страницы: 60

NANOCOLOR UV/VIS II

Бренд: Macherey-Nagel Страницы: 99

Бренд: Hanna Instruments Страницы: 9

Бренд: Parkside Страницы: 120

Бренд: Palstar Страницы: 15

Smart Air Quality Monitor

Бренд: Lennox Страницы: 28

Бренд: Roland Страницы: 96

Бренд: FM Marin Страницы: 8

Thermo Scientific iCE 3000 Series

Бренд: ThermoFisher Scientific Страницы: 42

Бренд: Isspro Страницы: 2

Бренд: Hanna Instruments Страницы: 12

Бренд: Trotec Страницы: 3

Бренд: Omega Страницы: 24

Бренд: RADWAG Страницы: 12

Бренд: DynAmp Страницы: 43

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды