Endress+Hauser Smartec S CLD132 Скачать руководство пользователя страница 8

Страница: 8 / 44

Wiring

Smartec S CLD132/134 PROFIBUS-PA/-DP

Hauser

Wiring

WARNING

Device is energized

Improper connection can cause injury or death.

‣

The electrical connection must only be carried out by a certified electrician.

‣

Technical personnel must have read and understood the instructions in this manual and
must adhere to them.

‣

Prior to beginning

any wiring work, make sure voltage is not applied to any of the cables.

3.1

Electrical connection

Proceed as follows to connect the bus cable to the transmitter:

Loosen the 4 Phillips screws on the housing cover and remove the cover.

WARNING

Instrument is energized

Inproper connection can cause injury or death.

‣

Make sure the instrument is disconnected from the power source before you remove the
cover frame.

Remove the cover frame from the terminal blocks. To do this, introduce a screwdriver in
the recess (A) according to



2 and push the tab inward (B).

Thread the cables through the open cable glands into the connection compartment.

Cable connection for PA devices:

Connect the cable wires of the bus cable in

accordance with



3 to the terminal block. Mixing up the polarity of the PA+ and

PA- connections does not have any influence on operation. The bus cable can be
connected to the PA device via the Pg cable gland or an M12 plug.

Cable connection for DP devices:

Connect the cable wires of the bus cable in

accordance with



7 to the terminal block.

Tighten the cable gland.

Close the housing cover.

a0005891

Fig. 2:

Bus cable connection Smartec S PROFIBUS

Port for DIL switch

Cover frame

Fuse

Removable electronics box

Terminals

Housing ground

Содержание Smartec S CLD132













































Результаты поиска

Содержание Smartec S CLD132

Отзывы:

Похожие инструкции для Smartec S CLD132

Бренды по названию

Популярные бренды

Endress+Hauser Smartec S CLD132, Руководство по эксплуатации

Результаты поиска

Содержание Smartec S CLD132

Отзывы:

Похожие инструкции для Smartec S CLD132

Бренды по названию

Популярные бренды