Endress+Hauser Proline Fieldcheck Скачать руководство пользователя страница 26 | Manualshive

Страница: 26 / 104

background image

Wiring

Proline Fieldcheck

26

Hauser

3.11

Connecting to Prosonic Flow 90, 93
wall-mount housing

!

Note!
Fieldcheck can only be used with devices with software version 1.06.xx or higher.

"

Caution!
Connect the ground terminals on the cables to the uninsulated housing components or to the
ground terminals in the connection compartment.

1.

Remove the cover of the connection compartment (4).

2.

Disconnect the sensor signal cables from the connection plate (5).

3.

Connect the connectors of the Simubox cable with the amplifier sockets and the Fieldcheck
socket on the connection plate (5).

!

Note!

The SYNC connector of the Simubox cable must be connected to the Fieldcheck socket on the
connection plate.

4.

Connect Fieldcheck to the current and frequency outputs of the transmitter



(terminal pairs 22/23, 24/25 or 26/27).

!

Note!

The configuration of the outputs depends on the product type and the order version of the
tested transmitter. To find out which terminal pairs are assigned to the outputs, see the
"Wiring" section of the flowmeter Operating Instructions.

5.

Connect Fieldcheck to the service connector (6).

a0001810

Fig. 19:

Connecting Fieldcheck to Prosonic Flow 93 (wall-mount housing)

1

Fieldcheck flow simulator

2

Simubox

3

Transmitter wall-mount housing

4

Connection compartment cover

5

Connection plate with amplifier sockets for sensor signal cable and Fieldcheck socket

6

Service connector

!

Note!
On the connection plate of the Prosonic Flow 90 wall-mount housing, only the CH1/up and



CH1/down amplifier sockets are assigned. When connecting Fieldcheck, the appropriately labeled
connectors of the Simubox cable are connected to the amplifier sockets and the SYNC connector of
the Simubox cable is plugged into the Fieldcheck socket on the connection plate.

1

2

22 23

20 21

24 25 26 27

3

4

5

6

2

1

up down

CH1

Field-
check

up down

CH2

«
...
24
25
26
27
28
...
»

Содержание Proline Fieldcheck









































































































Отзывы:

Нет отзывов

Похожие инструкции для Proline Fieldcheck

Бренд: Labom Страницы: 5

Бренд: Oakton Страницы: 16

Бренд: Vega Страницы: 28

Бренд: Vega Страницы: 20

Бренд: KBR Страницы: 12

Бренд: Divertug Страницы: 47

Бренд: Ramsey Electronics Страницы: 40

Бренд: PASCO Страницы: 13

Simple Precision OWD

Бренд: KAM Страницы: 41

Бренд: NI Страницы: 20

Бренд: Teledyne Lecroy Страницы: 8

Бренд: RIDGID Страницы: 4

Бренд: gaskatel Страницы: 22

Бренд: Jula Страницы: 17

Бренд: Keithley Страницы: 104

Bellingham+Stanley OPTi

Бренд: Xylem Страницы: 2

CP-4900 Micro-GC

Бренд: Varian Страницы: 21

Бренд: Proceq Страницы: 36

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды