Empire DVL36BP30N-1 страница 65 Скачать руководство пользователя

Страница: 65 / 68

41978-2-0321

Page 65

MAINTENANCE AND SERVICE (CONT’D)

Figure 65

When installing the Glass Frame, do not pull on the Spring-Latch Ring if the ring is flipped backwards as shown above.
Flip the ring forwards with your fingers or the Spring-Latch Tool before pulling on the Spring-Latch.

WHEN INSTALLING THE GLASS FRAME, DO NOT PULL ON THE SPRING-LATCH RING IF THE RING IS FLIPPED

BACKWARDS AS SHOWN ABOVE. FLIP THE RING FORWARDS WITH YOUR FINGERS OR THE SPRING-LATCH TOOL

BEFORE PULLING ON THE SPRING LATCH

WHEN INSTALLING THE GLASS FRAME, DO NOT PULL ON THE SPRING-LATCH RING IF THE RING IS FLIPPED

BACKWARDS AS SHOWN ABOVE. FLIP THE RING FORWARDS WITH YOUR FINGERS OR THE SPRING-LATCH TOOL

BEFORE PULLING ON THE SPRING LATCH

TO ACCESS THE BURNER, ONLY THE SCREWS

POINTED OUT ABOVE NEED TO BE REMOVED -

THE OTHER BURNER SURROUND SCREWS MAY

BE LEFT IN PLACE

Figure 66

To access the burner, only the screws pointed out above need to be removed. The other burner surround screws may
be left in place.

Содержание DVL36BP30N-1





































































Результаты поиска

Содержание DVL36BP30N-1

Отзывы:

Похожие инструкции для DVL36BP30N-1

Бренды по названию

Популярные бренды

Empire DVL36BP30N-1, Руководство по установке

Результаты поиска

Содержание DVL36BP30N-1

Отзывы:

Похожие инструкции для DVL36BP30N-1

Бренды по названию

Популярные бренды