Empire DVL36BP30N-1 страница 21 Скачать руководство пользователя

Страница: 21 / 68

41978-2-0321

Page 21

Termination clearance for buildings with combustible and noncombustible exteriors.

VENT TERMINATION CLEARANCES

Figure 13

VERTICAL SIDEWALL INSTALLATIONS
IMPORTANT!

Minimum clearance between vent pipes

and combustible materials is 3 inch (76 mm) on top, and 1

inch(25 mm) on bottom and sides.

IMPORTANT!

When vent termination exits through foundation

less than 20 inch (508 mm) below siding outcrop, the vent pipe

must extend outward so that the horizontal vent termination is

located flush to, or beyond the outcrop siding.

Information on Various Venting Routes and Components

IMPORTANT:

It is always best to locate the fireplace in such a way

that minimizes the number of offsets and horizontal vent length.
Since it is very important that the venting system maintain its

balance between the combustion air intake and the flue gas

exhaust, certain limitations as to vent configurations apply and

must be strictly adhered to.

The graph showing the relationship between vertical and

horizontal side wall venting will help to determine the various vent

lengths allowable.
The horizontal vent run refers to the total length of vent pipe from

the flue collar of the fireplace to the face of the outer wall.

Venting termination shall not be recessed into wall or siding.

ATTENTION: Vinyl Soffit, Vinyl Ceiling, Vinyl Overhang Disclaimer

Clearances are to heat resistant material (i.e. wood, metal). This

does not include vinyl. Empire Comfort Systems Inc. will not be

held responsible for heat damage caused from terminating under

vinyl overhangs, vinyl ceilings or vinyl ventilated/unventilated soffits.

RECESSED LOCATION

OUTSIDE CORNER

INSIDE CORNER

“A” = COMBUSTIBLE 9” (229mm)

= NONCOMBUSTIBLE 2” (51mm)

“F” = COMBUSTIBLE 6” (152mm)

= NONCOMBUSTIBLE 6” (152mm)

BALCONY

WITH PERPENDICULAR SIDE WALL

BALCONY

WITH NO SIDE WALL

“C” = CLEARANCE FROM CORNER

IN RECESSED LOCATION
COMBUSTIBLE 9” (229mm)
NONCOMBUSTIBLE 2” (51mm)

“D” = MINIMUM WIDTH FOR BACK WALL

OF A RECESSED LOCATION
COMBUSTIBLE 38” (965mm)
NONCOMBUSTIBLE 24” (610mm)

“E” = MAXIMUM DEPTH OF 48” (1219mm)

FOR RECESSED LOCATION

“G” = COMBUSTIBLE 9” (229mm)

= NONCOMBUSTIBLE 2” (51mm)

“H” = COMBUSTIBLE 18” (457mm)

= NONCOMBUSTIBLE 12” (305mm)

“I” = COMBUSTIBLE 12” (457mm)

= NONCOMBUSTIBLE 12” (305mm)

Содержание DVL36BP30N-1





































































Результаты поиска

Содержание DVL36BP30N-1

Отзывы:

Похожие инструкции для DVL36BP30N-1

Бренды по названию

Популярные бренды

Empire DVL36BP30N-1, Руководство по установке

Результаты поиска

Содержание DVL36BP30N-1

Отзывы:

Похожие инструкции для DVL36BP30N-1

Бренды по названию

Популярные бренды