Empire Comfort Systems DVCT40CSP95KN-1 Series Скачать руководство пользователя страница 4

Страница: 4 / 44

41521-2-0520

Page 4

BEFORE YOU START

Television Considerations

Installing a television above a fireplace has become increasingly

popular; however, the area above any fireplace gets hot and most

TV manufacturers recommend against placing their products near

a heat source.
If you install a television above this fireplace, Empire Comfort

Systems accepts no responsibility for damage or injuries. Follow

the television manufacturer’s installation instructions, including any

recommendations regarding proximity to heat sources.
If you have a TV above your fireplace, turn off the fireplace and let it

cool completely before servicing or touching any buttons on the TV.

Samples, Warnings, and Definitions:

DANGER

Indicates a hazardous situation which, if not avoided, will

result in death or serious injury.

WARNING

Indicates a hazardous situation which, if not avoided,

could result in death or serious injury.

CAUTION

Indicates a hazardous situation which, if not avoided,

could result in minor or moderate injury.

NOTICE:

Addresses practices not related to personal injury.

Read all instructions before starting installation and

follow them carefully to ensure safety. Failure to follow

the instructions will void the warranty and may cause

a fire hazard.

The warranty will be voided by, and the warranter disclaims

any responsibility for the following actions:

•

Installation by anyone other than the dealer or his agent.

•

Installation of any damaged fireplace or component.

•

Modification of the fireplace or direct vent system.

•

Installation other than as instructed by Empire Comfort Systems.

•

Improper positioning of logs, glass door, or accessories.

•

Installation and/or use of any component part not

manufactured or approved by Empire Comfort Systems.

All correspondence should refer to complete Model Number,

Serial Number and type of gas. Fill out the Homeowner

Reference Section on

(Page 7).

Unpacking The Fireplace

1. Remove the outer boards/crate by removing screws.
2. Cut away shrink-wrap material around the unit. Retain

instruction manual and instruction sheets.

3.  Remove (2) screws securing unit to pallet.
4.  Get help to lift unit off of the pallet using the handles.
5.  Remove non-combustible board from the pallet and place in

a safe location. It will be needed for installation.

6. Logs may remain in unit until installation in wall. Instruction

sheet from step #2 shows how to remove barrier screen and

glass door.

Содержание DVCT40CSP95KN-1 Series













































Результаты поиска

Содержание DVCT40CSP95KN-1 Series

Отзывы:

Похожие инструкции для DVCT40CSP95KN-1 Series

Бренды по названию

Популярные бренды

Empire Comfort Systems DVCT40CSP95KN-1 Series, Руководство по установке

Результаты поиска

Содержание DVCT40CSP95KN-1 Series

Отзывы:

Похожие инструкции для DVCT40CSP95KN-1 Series

Бренды по названию

Популярные бренды