Empire Comfort Systems DVCT40CSP95KN-1 Series Скачать руководство пользователя страница 24

Страница: 24 / 44

41521-2-0520

Page 24

VENTING FIREPLACE (CONT’D)

Positioning the Fireplace

Determine the exact position of the appliance so the direct-vent

termination will be centered (if possible) between two studs. This

will avoid any extra framing. All vent kit pipes should be assembled

on the unit after the unit is moved into the final position.

Cutting the Hole

After the fireplace has been positioned in its permanent location,

cut the hole through the exterior wall of the house. This hole must

be 10 inches (254mm) high x 10-5/8 inches(270mm) wide with its

center line determined by the amount of vertical rise and horizontal

run of the termination.

See Figure 38.

When locating the hole the

bottom of the cap must be 12 inches (305mm) above the ground

level, and top of the cap must be no less than 18 inches (457mm)

below a combustible projection, and no closer than 9 inches (229mm)

to any wall running parallel to vent termination.
For installations requiring a vertical rise on the exterior of the

building, 14-inch and 36-inch tall Snorkel Terminations are available.

Follow the same installation procedures as used for standard

Horizontal Terminations. If the Snorkel Termination must be installed

below grade (i.e. basement applications, proper drainage must be

provided to prevent water from entering the Snorkel Termination.

See Figure

39.

Do not attempt to enclose the Snorkel within the

wall or any other type of enclosure.

GENERIC MODEL SHOWN

Figure 38

Below - Grade Installation

When it is not possible to meet the required vent termination

clearances of 12 inch (305 mm) above grade level, a snorkel kit is

recommended. It allows installation depth down to 7 inch (178 mm)

below grade level. The 7 inch (178 mm) is measured from the center

of the horizontal vent pipe as it penetrates through the wall.

Ensure the sidewall venting clearances are observed.

If the venting system is installed below ground, protect

the vent with a window well that has proper drainage.

6” (152mm)
MINIMUM

PIPE STRAP

48”

(1219mm)

COMBUSTIBLE
PROJECTION

18” (457mm)

MINIMUM

12” MINIMUM ABOVE GRADE

OR AVERAGE SNOWFALL

SNORKEL

ADEQUATE
DRAINAGE

TYPICAL BASEMENT INSTALLATION

GENERIC MODEL SHOWN

Figure 39

Содержание DVCT40CSP95KN-1 Series













































Результаты поиска

Содержание DVCT40CSP95KN-1 Series

Отзывы:

Похожие инструкции для DVCT40CSP95KN-1 Series

Бренды по названию

Популярные бренды

Empire Comfort Systems DVCT40CSP95KN-1 Series, Руководство по установке

Результаты поиска

Содержание DVCT40CSP95KN-1 Series

Отзывы:

Похожие инструкции для DVCT40CSP95KN-1 Series

Бренды по названию

Популярные бренды