Empire Comfort Systems DVCT40CSP95KN-1 Series Скачать руководство пользователя страница 40

Страница: 40 / 44

41521-2-0520

Page 40

DO NOT OPERATE THIS APPLIANCE WITHOUT GLASS FRONT PANEL INSTALLED

Before enclosing the vent pipe assembly, operate the appliance to ensure it is venting properly.

IMPORTANT SAFETY INFORMATION

WARNING

1. “Due to high temperatures, the appliance should be

located out of traffic and away from furniture and

draperies.”

2. “Children and adults should be alerted to the hazards

of high surface temperature and should stay away to

avoid burns or clothing ignition.”

3. “Young children should be carefully supervised when they

are in the same room as the appliance. Toddlers, young

children, and others may be susceptible to accidental

contact burns. A physical barrier is recommended if there

are at-risk individuals in the house. To restrict access to a

fireplace or stove, install an adjustable safety gate to keep

toddlers, young children, and other at-risk individuals out

of the room and away from hot surfaces.”

4. For appliances requiring a barrier, as determined under

Clause 5.15.4: “A barrier designed to reduce the risk of

burns from the hot viewing glass is provided with this

appliance and shall be installed for the protection of

children and other at-risk individuals.”

5. “If the barrier becomes damaged, the barrier shall

be replaced with the manufacturer’s barrier for this

appliance.

”

6. “Clothing or other flammable material should not be

placed on or near the appliance.”

7. “Any safety screen, guard, or barrier removed for

servicing an appliance must be replaced prior to

operating the appliance” (see Clause 4.1.6).

8. “Installation and repair should be done by a qualified

service person. The appliance should be inspected

before use and at least annually by a professional service

person. More frequent cleaning might be required due to

excessive lint from carpeting, bedding material, et cetera.

It is imperative that control compartments, burners, and

circulating air passageways of the appliance be kept

clean.”

9. The instructions for an appliance optionally for use

with glass doors (or equivalent) shall state that, “Only

doors certified with the appliance shall be used.”

10. The instructions for an appliance not intended for use

with glass doors (or equivalent) shall emphasize that

the appliance is not for use with glass doors.

11. Where applicable, provide a means by which the

consumer can identify the barrier, (such as graphic

representation, clear description, or reference marking).

WARNING

CARBON MONOXIDE POISONING HAZARD

Failure to follow the steps outlined below for each appliance

connected to the venting system being placed into operation

could result in carbon monoxide poisoning or death.

The following steps shall be followed for each appliance

connected to the venting system being placed into operation,

while all other appliances connected to the venting system

are not in operation:
1. Seal any unused openings in the venting system.
2. Inspect the venting system for proper size and horizontal

pitch, as required in the

National Fuel Gas Code ANSI

Z223.1/NFPA 54

the National Gas and Propane

Installation Code

CSA B149.1 and these instructions.

Determine that there is no blockage or restriction,

leakage, corrosion and other deficiencies which could

cause an unsafe condition.

3. As far as practical, close all building doors and

windows and all doors between the space in which

the appliance(s) connected to the venting system are

located and other spaces of the building.

4. Close fireplace dampers.

5. Turn on clothes dryers and any appliance not connected

to the venting system. Turn on any exhaust fans, such

as range hoods and bathroom exhausts, so they are

operating at maximum speed. Do not operate a summer

exhaust fan.

6. Follow the lighting instructions. Place the appliance

being inspected into operation. Adjust the thermostat

so appliance is operating continuously.

7. Test for spillage from draft hood equipped appliances

at the draft hood relief opening after 5 minutes of main

burner operation. Use the flame of a match or candle.

8. If improper venting is observed during any of the

above tests, the venting system must be corrected

in accordance with

National Fuel Gas Code

, ANSI

Z223.1/NFPA and/or

National Gas and Propane

Installation Code

, CSA B149.1.

9. After it has been determined that each appliance

connected to the venting system properly vents when

tested as outlined above, return doors, windows,

exhaust fans, fireplace dampers and any other gas-fired

burning appliance to their previous conditions of use.

Содержание DVCT40CSP95KN-1 Series













































Результаты поиска

Содержание DVCT40CSP95KN-1 Series

Отзывы:

Похожие инструкции для DVCT40CSP95KN-1 Series

Бренды по названию

Популярные бренды

Empire Comfort Systems DVCT40CSP95KN-1 Series, Руководство по установке

Результаты поиска

Содержание DVCT40CSP95KN-1 Series

Отзывы:

Похожие инструкции для DVCT40CSP95KN-1 Series

Бренды по названию

Популярные бренды