Empire Comfort Systems DVCT40CSP95KN-1 Series Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 44

background image

41521-2-0520

Page 11

Figure 6

Vertical Sidewall Installations

Important!

Minimum clearance between vent pipes and combustible

materials is 3 inch (76 mm) on top, and 1 inch (25 mm) on bottom

and sides.

Important!

When vent termination exits through foundation less

than 20 inch (508 mm) below siding outcrop, the vent pipe must

extend outward so that the horizontal vent termination is located

flush to, or beyond the outcrop siding.

Information on Various Venting Routes and Components

Important:

Locate the fireplace in such a way that minimizes the

number of offsets and horizontal vent length.
Since it is very important that the venting system maintain its balance

between the combustion air intake and the flue gas exhaust, certain

limitations as to vent configurations apply and must be strictly

adhered to.

The graph showing the relationship between vertical and horizontal

side wall venting will help to determine the various vent lengths

allowable.
The horizontal vent run refers to the total length of vent pipe from

the flue collar of the fireplace to the face of the outer wall.
Venting termination shall not be recessed into wall or siding.

ATTENTION: Vinyl Soffit, Vinyl Ceiling, Vinyl Overhang

Disclaimer

Clearances are to heat resistant material (i.e. wood, metal). This

does not include vinyl. Empire Comfort Systems Inc. will not be held

responsible for heat damage caused from terminating under vinyl

overhangs, vinyl ceilings or vinyl ventilated/unventilated soffits.

Termination clearance for buildings with combustible and noncombustible exteriors.

VENT TERMINATION CLEARANCES

«
...
9
10
11
12
13
...
»

Содержание DVCT40CSP95KN-1 Series













































Отзывы:

Нет отзывов

Похожие инструкции для DVCT40CSP95KN-1 Series

Бренд: Valcourt Страницы: 95

LEGEND G4 780IN (NG)

Бренд: Valor Страницы: 44

Бренд: Valor Страницы: 30

Бренд: Valor Страницы: 12

CHURCHILL 32-810-58

Бренд: Valor Страницы: 29

Бренд: Valor Страницы: 9

Бренд: Valor Страницы: 56

President ZC Cast Front 536CXB

Бренд: Valor Страницы: 18

Portrait 569 Ledge Front

Бренд: Valor Страницы: 18

Бренд: Valor Страницы: 39

Бренд: Valor Страницы: 4

Бренд: Valor Страницы: 6

Бренд: Valor Страницы: 6

Бренд: Valor Страницы: 78

Бренд: Valor Страницы: 58

Portrait Series

Бренд: Valor Страницы: 6

Бренд: Valor Страницы: 10

OXYSAFE CONTOUR 3290

Бренд: Valor Страницы: 5

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды