Empire Comfort Systems DVCT40CSP95KN-1 Series Скачать руководство пользователя страница 12

Страница: 12 / 44

41521-2-0520

Page 12

VENT TERMINATION CLEARANCES (CONT’D)

Canadian Installations1

US Installations2

Canadian Installations1 US Installations2

A= Clearance above grade,

veranda, porch, deck, or

balcony

12-in (30cm)

I= Clearance to service

regulator vent outlet

3ft (91cm)

61-in

B= Clearance to window or

door that may be open

12-in (30cm) for

appliances >

10,000Btuh (3kW) and

≤ 100,000 Btuh (30kW)

9-in (23cm) for

appliances >

10,000Btuh

(3kW) and ≤ 50,000

Btuh (15kW)

J= Clearance to non-me

chanical air supply

inlet to building or the

combustion air inlet to

any other appliance

12-in (30cm) for

appliances > 10,000

Btuh (3kW) and ≤

100,000 Btuh (30kW)

9-in (23cm) for

appliances > 10,000Btuh

(3kW) and ≤ 50,000Btuh

(15kW)

C= Clearance to permanent

ly closed window

12-in (30cm)

12in (30cm)

K= Clearance to a me

chanical air supply inlet 6ft (1.83m)

3ft (91cm) above if within

10ft (3m) horizontally

D= Vertical clearance venti

lated soffit located above

the terminal within a hor

izontal distance of 2 feet

(61cm) from the center

line of the terminal

18-in

L= Clearance above

paved sidewalk or

paved driveway

located on public

property

7ft (2.13m) †

7ft (2.13m)

E= Clearance to unventilat

ed soffit

18-in

M= Clearance under

veranda, porch

deck, or balcony

12-in (30cm) ‡

12-in (30cm)

F= Clearance to outside

corner

See previous page.

In accordance with the current CSA B149.1, Natural Gas and Propane

Installation Code

G= Clearance inside corner

See previous page.

In Accordance with the current ANSI Z223.1/NFPA 54, National Fuel Gas Code

H= Clearance to each side

of center line extended

above meter/regulator

assembly

3ft (91cm) within a

height 15ft (4.5m)

above the meter/regula

tor assembly

3ft (91cm)

†

A vent shall not terminate directly above a sidewalk or paved driveway that

is located between two single family dwellings and serves both dwellings

ATTENTION: Vinyl Soffit, Vinyl Ceiling, Vinyl Overhang

Disclaimer

Clearances are to heat resistant material (i.e. wood, metal). This

does not include vinyl. Empire Comfort Systems Inc. will not be

held responsible for heat damage caused from terminating under

vinyl overhangs, vinyl ceilings or vinyl ventilated/unventilated soffits.

‡

Permitted only if veranda,, porch, deck, or balcony is fully open on a mini

mum of two sides beneath the floor.

For clearances not specified in ANSI Z223.1/NFPA 54 or CSA B149.1, one

of the following shall be indicated:

Clearance in accordance with local installation codes and the requirements of the

gas supplier.

Содержание DVCT40CSP95KN-1 Series













































Результаты поиска

Содержание DVCT40CSP95KN-1 Series

Отзывы:

Похожие инструкции для DVCT40CSP95KN-1 Series

Бренды по названию

Популярные бренды

Empire Comfort Systems DVCT40CSP95KN-1 Series, Руководство по установке

Результаты поиска

Содержание DVCT40CSP95KN-1 Series

Отзывы:

Похожие инструкции для DVCT40CSP95KN-1 Series

Бренды по названию

Популярные бренды