manualshive.com logo in svg

Empire Comfort Systems DVCT40CSP95KN-1 Series, Руководство по установке

"Установочный инструкции Руководство для продукта Empire Comfort Systems DVCT40CSP95KN-1 Series доступно для бесплатного скачивания с {веб-сайта}. Этот документ является неотъемлемой частью приобретения продукта, обеспечивая правильную установку и безопасное использование. Получите доступ к этому важному руководству прямо сейчас."

Поделиться
Скачать
background image

41521-2-0520

Page 3

ATTENTION INSTALLER:

Follow This Standard Work Checklist

This standard work checklist is to be used by the installer in conjunction with, not instead of, the instruction manual.

Customer:  _____________________________________
Lot/Address: ___________________________________
_______________________________________________
Model:  ________________________________________
Serial # ________________________________________

Date Installed: _________________________________  
Fireplace Location: _____________________________
Installer: ______________________________________  
Dealer Phone #: ________________________________
______________________________________________  

Empire recommends the following:

• 

Photograph the installation and copying this checklist for your file.

• 

Keep this checklist visible on the fireplace until the installation is complete.

Comments:

 

Further description of the issues, who is responsible (Installer/Builder/Other, etc) and corrective action needed: 

___________________________________________________________________________________________________________

Comments communicated to party responsible

 _____________________

by

 _____________________

on

 ______________________

DVCT40CSP95KN-1

FIREPLACE INSTALLATION

 

COMMENTS

Verified clearances to combustibles. (pg. 10)  ......................................................................

 

o 

 ____________________

Fireplace is leveled and secured.  ........................................................................................

 

o

  ____________________

VENTING / CHIMNEY

Venting configuration complies to vent diagrams. (pg. 25)  ..................................................

 

o

  ____________________

Venting installed, locked, secured in place with correct clearance.  .....................................

 

o

  ____________________

Firestops installed. ...............................................................................................................

 

o

  ____________________

Exterior wall/roof flashing installed and sealed. ...................................................................

 

o

  ____________________

Terminations installed and sealed. (pgs. 27-29)  ..................................................................

 

o

  ____________________

Light unit and test venting before enclosing the fireplace. ...................................................

 

o

  ____________________

ELECTRICAL (pgs. 14-15)

Unswitched power (110-120 VAC) provided to the appliance.  ............................................

 

o

  ____________________

GAS (pg. 13)

Proper appliance for fuel type. .............................................................................................

 

o

  ____________________

Was a conversion performed? ..............................................................................................

 

o 

Yes 

o 

No

Leak check performed and inlet pressure verified ................................................................

 

o

  ____________________

FINISHING ( pg. 17)

Non-combustible board used as required.............................................................................

 

o 

 ____________________

Verified all clearances meet installation manual requirements.  ...........................................

 

o 

 ____________________

Mantels and wall projections comply with installation manual requirements.  ......................

 

o 

 ____________________

Granite or Clean Face finishing complete and complies with clearance                                           
requirements in installation manual.  ....................................................................................

 

o 

 ____________________

Barrier screen for glass properly installed.  ..........................................................................

 

o 

 ____________________

FIREPLACE SETUP

All packaging and protective materials removed (inside & outside of appliance) . ...............

 

o

 

  ____________________

Media installed correctly.  .....................................................................................................

 

o

  

 ____________________

Firebox glass assembly cleaned, installed, and secured.  ...................................................

 

o

 

  ____________________

Accessories installed properly.  ............................................................................................

 

o

  ____________________

Manual envelope and all of its contents are removed from inside/outside the        
appliance and given to party responsible for use and operation.  ........................................

 

o 

 ____________________

Started Appliance and verified no gas leaks exist.  ..............................................................

 

o

 

  ____________________

Содержание DVCT40CSP95KN-1 Series













































Отзывы:

Нет отзывов

Похожие инструкции для DVCT40CSP95KN-1 Series

Valor Heartbeat OXYSAFE 2 Owner'S Manual preview
Heartbeat OXYSAFE 2
Бренд: Valor Страницы: 10
Heatilator Heatilator Icon Series Brochure & Specs preview
Heatilator Icon Series
Бренд: Heatilator Страницы: 2
Astria Fireplaces Atlas36ZP2 Installation And Operation Instructions Manual preview
Atlas36ZP2
Бренд: Astria Fireplaces Страницы: 20
Desa B36L-MC Owner'S Operation And Installation Manual preview
B36L-MC
Бренд: Desa Страницы: 44
Desa (V)KC42NE SERIE Owner'S Operation And Installation Manual preview
(V)KC42NE SERIE
Бренд: Desa Страницы: 40
Bali SRGF21901 Owner'S Manual preview
SRGF21901
Бренд: Bali Страницы: 16
Xaralyn Levico Manual preview
Levico
Бренд: Xaralyn Страницы: 11
Burley Surefire FCC 16 User, Installation & Servicing Instructions preview
Surefire FCC 16
Бренд: Burley Страницы: 32
Room&Board 1112LP-TGR Owner'S Manual preview
1112LP-TGR
Бренд: Room&Board Страницы: 32
Spark Fire Ribbon Direct VEnt Slim 26" Installation And Operation Manual preview
Fire Ribbon Direct VEnt Slim 26"
Бренд: Spark Страницы: 48
Adobelite KIVA 18 Ornito Installation Manual preview
KIVA 18 Ornito
Бренд: Adobelite Страницы: 23
eligent EF450SL Instruction Manual preview
EF450SL
Бренд: eligent Страницы: 4
Stellar Hearth 4-SS-2-GL Installation And Operating Manual preview
4-SS-2-GL
Бренд: Stellar Hearth Страницы: 37
Valor Fires Wellington Surround Installation Manual preview
Wellington Surround
Бренд: Valor Fires Страницы: 8
pleasant hearth Fireplace Glass Door Owner'S Manual preview
Fireplace Glass Door
Бренд: pleasant hearth Страницы: 27
Montigo L42DF ST Installation & Maintenance Manual preview
L42DF ST
Бренд: Montigo Страницы: 40
Twin-Star International ChimneyFree 1142880 Manual preview
ChimneyFree 1142880
Бренд: Twin-Star International Страницы: 50
Valor tuscany 637 Owner'S Manual preview
tuscany 637
Бренд: Valor Страницы: 8

Бренды по названию

Популярные бренды

Загрузить еще бренды