Empire Comfort Systems DVCT40CSP95KN-1 Series Скачать руководство пользователя страница 18

Страница: 18 / 44

41521-2-0520

Page 18

INSTALLATION (CONT’D)

ON TOP AND SIDES AND

BETWEEN 1/2” TO 3/4” AT BOTTOM

Figure 21

Horizontal Vent Clearance

For horizontal vent, maintain 1 inch of clearance to the bottom

and sides of vent, and 6 inches of clearance to combustibles

above the vent pipe.

See Figure 223.

Vertical Vent Clearance

For vertical vent, maintain a minimum 1 of inch clearance to

combustibles.

NOTICE:

Maintain 1 of inch of clearance to combustibles around

vertical vent pipe.

See Figure 22.

For horizontal vent systems,

maintain a minimum 1 inch of clearance from the bottom and sides

of the vent to combustibles and a 3 inches of

clearance above the

vent pipe

to combustibles.

See Figures 22 and 23.

VENT PIPE

1” MINIMUM CLEARANCE

AROUND VENT PIPE

Figure 22

TOP OF VENT

COMBUSTIBLES NOT
ALLOWED IN SHADED
AREA

6” (152 mm)

8” DIAMETER
INTAKE VENT

1” (25 mm)

5” DIAMETER FLUE

1” (25 mm)

Horizontal Vent Clearances - Figure 23

NOTE:

Top clearance through outside wall is 3 inches.

ATTENTION:

Cold climate installation recommendation: When

installing this unit against an exterior wall, the exterior wall must

be insulated to conform to applicable insulation codes. The

fireplace outer wrapper is not considered a thermal barrier and

can allow air infiltration. Care should be taken to properly seal

the chase area so air infiltration is kept to a minimum and drafts

do not occur through the fireplace.

Vent Runs

In planning the installation, you must install certain components

before the fireplace is secured in position. These include the

direct-vent system, gas piping, and the electrical wiring.

The appliance can be mounted on any of the following surfaces:
1. A flat, hard combustible or non-combustible surface.

2. A raised wooden platform.

3. Four corner supports(such as masonry blocks). These supports

must be positioned so they contact all four perimeter edges on

the bottom of the unit.

OVERLAP TOP EDGE OF

NON-COMBUSTIBLE

BOARD WITH EXTERIOR

WEATHER BARRIER
SEAL THE PERIMETER OF

THE OUTDOOR KIT WITH

(300°F (149°C) SEALANT
FACING MATERIAL MUST

OVERLAP THE OUTDOOR

KIT PERIMETER BY AT

LEAST 1" ON TOP AND

SIDES AND BETWEEN 1/2"

TO 3/4" AT BOTTOM
FACING MATERIAL MAY

OVERLAP THE OUTDOOR

KIT UP TO 1/2" AWAY FROM

THE KIT OPENING
SEAL THE INTERFACE

BETWEEN THE OUTDOOR

KIT AND THE FACING

MATERIAL WITH AN

EXTERIOR CAULK

Содержание DVCT40CSP95KN-1 Series













































Результаты поиска

Содержание DVCT40CSP95KN-1 Series

Отзывы:

Похожие инструкции для DVCT40CSP95KN-1 Series

Бренды по названию

Популярные бренды

Empire Comfort Systems DVCT40CSP95KN-1 Series, Руководство по установке

Результаты поиска

Содержание DVCT40CSP95KN-1 Series

Отзывы:

Похожие инструкции для DVCT40CSP95KN-1 Series

Бренды по названию

Популярные бренды