Emerson Rosemount 975HR Скачать руководство пользователя страница 70 | Manualshive

Страница: 70 / 80

background image

NOTICE

The item letters in this procedure can be found in

Procedure

1. Place the flame simulator in a safe area, not exceeding 104 °F (40 °C).
2. Release the locking screw.
3. Unscrew the battery back cover (D) counter-clockwise.
4. Unscrew the locking disc (C) clockwise.
5. Pull out the battery from the flame simulator.
6. Connect the battery to the charger.
7. Charge for a maximum of two to three hours.
8. Disconnect the charger.
9. Insert the battery in the flame simulator.

10. Screw on the locking disc (C).
11. Screw on the back cover (D).
12. Lock the back cover with the locking screw.

D.1.6

Replace the battery

NOTICE

The item letters shown in this procedure can be found in

.

Procedure

1. Place the flame simulator on a table in a safe area, not exceeding 104 °F (40 °C).
2. Release the locking screw.
3. Unscrew the battery back cover (D) counter-clockwise.
4. Unscrew the locking disk (C) clockwise.
5. Pull out the battery from the flame simulator.
6. Insert the new battery pack in the simulator housing.

Use only Rosemount battery pack, PN 00975-9000-0012.

7. Screw on the locking disc (C).
8. Screw on the back cover (D).
9. Lock the back cover with the locking screw.

NOTICE

For more information, refer to the

Rosemount FS-HR-975 Flame Simulator Manual

(00809-0900-4975)

Accessories

Reference Manual

June 2021

00809-0100-4976

70

Emerson.com/Rosemount

Legacy

«
...
68
69
70
71
72
...
»

Содержание Rosemount 975HR

















































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount 975HR

SECURICAM Network DCS-900

Бренд: D-Link Страницы: 92

SECURICAM DCS-910

Бренд: D-Link Страницы: 7

Бренд: D-Link Страницы: 12

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 32

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 8

Бренд: D-Link Страницы: 110

Бренд: D-Link Страницы: 66

Бренд: D-Link Страницы: 9

Бренд: D-Link Страницы: 4

Бренд: D-Link Страницы: 6

Бренд: D-Link Страницы: 8

Бренд: OI Analytical Страницы: 133

Бренд: CAME Страницы: 80

Бренд: DAGE-MTI Страницы: 16

Бренд: NA-DE Страницы: 7

BugHunter Professional CR-01

Бренд: i4Technology Страницы: 9

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды