Emerson Rosemount 975HR Скачать руководство пользователя страница 35

Страница: 35 / 80

Figure 2-3: Tilt Mount Assembly Dimensions

To install the tilt mount:

Procedure

1. Place the tilt mount in its designated location and secure it with four (4) fasteners

through four (4) holes 0.14 in. (7 mm) in diameter. Use the four (4) screws and
spring washers according to the kit.
Refer to

Figure 2-3

Table 2-2

, and

Table 2-3

Note

You do not have to remove the tilt mount when removing the detector for
maintenance purposes.

2. Unpack the detector.
3. Place the detector with its conduit/cable entries pointing downwards on the

holding plate of the tilt mount. Secure the detector with 5/16-in. 18 UNC x 1-in.
screw to the tilt mount.

4. Release the horizontal and vertical locking screws using the supplied 3/16-in. hex

key, such that the detector can be rotated. Point the detector towards the
protected area and ensure the view of the area is unobstructed. Secure the detector
in position by tightening the locking screws on the tilt mount.

The detector is now correctly located, aligned, and ready to be connected to the system.

Reference Manual

Installing the detector

00809-0100-4976

June 2021

Rosemount 975HR

Legacy

Содержание Rosemount 975HR

















































































Результаты поиска

Содержание Rosemount 975HR

Отзывы:

Похожие инструкции для Rosemount 975HR

Бренды по названию

Популярные бренды

Emerson Rosemount 975HR, Справочное руководство

Результаты поиска

Содержание Rosemount 975HR

Отзывы:

Похожие инструкции для Rosemount 975HR

Бренды по названию

Популярные бренды