Emerson Rosemount 975HR Скачать руководство пользователя страница 47 | Manualshive

Страница: 47 / 80

background image

4

Maintenance and troubleshooting

This chapter deals with preventative maintenance, describes possible faults in detector
operation, and indicates corrective measures.

Ignoring these instructions may cause problems with the detector and may invalidate the
warranty. Whenever a unit requires service, please contact Emerson or its authorized
distributer for assistance.

4.1

Maintenance

This section describes the basic maintenance steps you should take to keep the detector in
good working condition.

4.1.1

General maintenance procedures

Only suitably qualified personnel who are familiar with local codes and practices should
perform maintenance. Maintenance requires ordinary tools.

Cleaning

Keep the detector as clean as possible. Clean the viewing window and the reflector of the
flame detector periodically.

The frequency of cleaning operations depends upon the local environmental conditions
and specific applications. The fire detection system designer will give his or her
recommendations.

To clean the detector viewing window and reflector:

Procedure

1. Disconnect power to the detector before proceeding with any maintenance,

including window/lens cleaning.

2. Use water and detergent and then rinse the viewing window with clean water.
3. Where dust, dirt, or moisture accumulates on the window, first clean only with a

soft optical cloth and detergent and then rinse with clean water.

4.1.2

Periodic maintenance procedures

In addition to preventive cleaning and maintenance, functionally test the detector every
six months or as dictated by local codes and regulations. Also perform these tests if the
detector has been opened for any reason.

Power-up procedure

Perform the power-up procedure every time power is restored to the system.

Follow the instructions described in

Reference Manual

Maintenance and troubleshooting

00809-0100-4976

June 2021

Rosemount 975HR

47

Legacy

«
...
45
46
47
48
49
...
»

Содержание Rosemount 975HR

















































































Отзывы:

Нет отзывов

Похожие инструкции для Rosemount 975HR

Бренд: RadiaCode Страницы: 42

Бренд: Panasonic Страницы: 44

Бренд: Panasonic Страницы: 32

HomeHawk KX-HNC800

Бренд: Panasonic Страницы: 2

BL-C10A - Network Camera - Pan

Бренд: Panasonic Страницы: 4

Бренд: Elkron Страницы: 12

Бренд: Eclipse Страницы: 48

Бренд: Eclipse Страницы: 52

Бренд: Eclipse Страницы: 48

Бренд: WATERGUARD Страницы: 2

Бренд: M-system Страницы: 3

Бренд: Samsung Wisenet Страницы: 16

Бренд: ACTi Страницы: 2

Бренд: Idis Страницы: 51

Бренд: IDS Страницы: 8

XRX300 LED Series

Бренд: WE-EF Страницы: 6

Бренд: MeiTrack Страницы: 8

Бренд: Allied Vision Technologies Страницы: 34

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды