Emerson Rosemount 975HR Скачать руководство пользователя страница 11

Страница: 11 / 80

•

Temperature: 2 (185 °F [85 °C])

•

Approvals: A1 (ATEX and IECEx flameproof)

NOTICE

Check your specific part numbers against the information in

Checking the product type

1.3

Features and benefits

The flame detector has the following features and benefits.

•

Detects hydrocarbons and hydrogen flames.

•

Detection range: Up to 215 ft. (65 m) for a 1 ft.

(0.1 m

) n-heptane fire.

•

Ultra high immunity to false alarms. See

Table 1-3

•

Advanced digital processing of the dynamic characteristics of fire: flickering, threshold,
correlation, and ratio.

•

Multi infrared channels: between two and five microns.

•

Field programmable sensitivity: four ranges to avoid zone crossover.

•

Built-in-test (BIT): manual and automatic (see

Built-in test (BIT)

•

Heated window: prevents effects of icing, snow, and condensation.

•

Electrical interface:

—

Dry contact relays

—

Communication network RS-485

—

0-20 mA output

•

HART

protocol: communication protocol (see

HART

protocol

•

Exde: integral junction box for easy wiring.

•

SIL-2: TÜV approved.

•

Hazardous area certification: ATEX, IECEx, FM, and CSA.

•

Functionality approval:

—

EN54-10 approved by VdS

—

FM approved per FM3260

•

Accessories are approved as part of ATEX and IECEx approval.

1.4

Principles of operation

1.4.1

Fire detection principle

Emerson designed this flame detector to detect hydrocarbon flames that produce CO

their combusion process and non-hydrocarbon flames that produce mainly water vapor

Reference Manual

Introduction

00809-0100-4976

June 2021

Rosemount 975HR

Legacy

Содержание Rosemount 975HR

















































































Результаты поиска

Содержание Rosemount 975HR

Отзывы:

Похожие инструкции для Rosemount 975HR

Бренды по названию

Популярные бренды

Emerson Rosemount 975HR, Справочное руководство

Результаты поиска

Содержание Rosemount 975HR

Отзывы:

Похожие инструкции для Rosemount 975HR

Бренды по названию

Популярные бренды