Emerson Rosemount 975HR Скачать руководство пользователя страница 55

Страница: 55 / 80

•

Operating temperature: +167 °F (+75 °C)

•

Storage temperature: +185 °F (+85 °C)

Low temperature

•

Designed to meet DNVGL-CG-0339, class D

•

Operating temperature: -57 °F (-50 °C)

•

Storage temperature: -65 °F (-55 °C)

Humidity

The Rosemount 975 detector conforms to DNVGL-CG-0339, class B.

Enclosure

The Rosemount 975 detector conforms to DNVGL-CG-0339, class C.

Water and dust

•

IP66 per EN60529

•

IP68 per EN60529

•

Dust: Completely protected against dust.

•

Liquids: Protected against immersion between 6 in. (15 cm) and
3 ft. (1 m) in depth. Protected against water jets from all
directions.

Vibration

The Rosemount 975 detector conforms to DNVGL-CG-0339, class B.

Table A-5: Electromagnetic Compatibility

This product is in conformance with EMC per EN50270.

Level per

Radiated immunity

EN61000-4-3

Conducted immunity

EN61000-4-6

Electrostatic discharge (ESD)

EN61000-4-2

Magnetic field

EN61000-4-8

Burst

EN61000-4-4

Surge

EN61000-4-5

Radiated emission

EN550022

Conducted emission

EN550022

CAUTION

To fully comply with EMC directive 2014/30/EU and protect against interference caused by
radio frequency interference and electromagnetic interference, shield the cable to the
detector and ground the detector. Ground the shield at the detector end.

Reference Manual

Specifications and reference data

00809-0100-4976

June 2021

Rosemount 975HR

Legacy

Содержание Rosemount 975HR

















































































Результаты поиска

Содержание Rosemount 975HR

Отзывы:

Похожие инструкции для Rosemount 975HR

Бренды по названию

Популярные бренды

Emerson Rosemount 975HR, Справочное руководство

Результаты поиска

Содержание Rosemount 975HR

Отзывы:

Похожие инструкции для Rosemount 975HR

Бренды по названию

Популярные бренды